Chicken feeder made from a sewer pipe. Chicken feeders made from PVC sewer pipes: types of designs and manufacturing tips

Raising chickens on personal plots allows you to supply your family with environmentally friendly and fresh meat and eggs. Chickens do not require labor-intensive daily grooming. Chickens do not eat much. They are unpretentious in food. But 70% of the time and money of keeping chickens goes into feeding them.

Even if the food is on the surface, chickens have an innate habit of digging it up. Therefore, they get into the food with their feet, scatter it, and turn over the feeders.

What it is?

This is a product that supplies food to chickens as the tray becomes empty. Any feeder consists of a hopper where food is poured and a tray, where the chickens peck it from. The farmer pours the feed into the bunker, from where it independently moves in portions to the feeding area.

The bin must be tightly closed to prevent the chickens from getting to the feed and eating it all at once or scattering it around the coop.

Having an automatic feeder, the farmer does not need to monitor feeding time and go to the chicken coop 3-4 times a day to add a new portion.

Feeders are divided according to the method of feeding:

Manufacturing requirements

The feeder should hold enough food to provide enough food for all the birds on the farm. When making a tray feeder, plan the length so that each chicken has 10-15 cm. For chickens, half that amount. There must be an approach to the feeders from any side so that the weaker ones are not pushed aside and are not left without food.
The feeder must have certain restrictions so that chickens do not have the opportunity to enter the bunker and scatter and dirty the feed.
It should be mobile, easy to fill, disassemble and clean.

Do-it-yourself feeders are made from plastic buckets and bottles, wood and iron. But the most inexpensive, easy to use and durable feeders are made from plastic PVC or sewer pipes.

Product Description

A plastic pipe feeder is the most reliable of all. It is attached to the wall and the chickens, in the process of feeding and searching for food, cannot turn it over and scatter the grain. Grain is consumed more economically.
One feeder made of pipes is enough for 20 chickens.
The longer the pipe, the more feed can be loaded there. Typically, this design can hold up to 10 kg of dry food and there will be no need to run to the chicken coop several times a day.
Plastic has no limitation on service life. The product is made in a couple of hours and can last for many decades.
Plastic pipes are very inexpensive and are available at any hardware store.

Feeders made of PVC pipes are available: with holes, with cutouts and with a tee. The choice of feed supply device depends on the size of the chicken coop and the location of the cages with the birds.

If you are concerned about the question of how to make a feeder with your own hands from polypropylene, plastic and other types of pipes, then you can see the photo:

Can I buy it in stores?

The choice of feeders in stores starts from the simplest bunkers to high-tech devices with a timer and a feed scattering function.

The price for the simplest bunker feeders is approximately 500-1000 rubles, but for high-tech products you will have to pay 5000-6000 rubles. The body material of the feeders also affects the price. A feeder made of ABS plastic costs 6.5 thousand rubles. Made of powder-coated steel 8.5 thousand rubles.

In stores you can find feeders completely ready for installation and use. They immediately have a food container and a tray.

It’s even better to make a feeder yourself from scrap materials.. This will cost much less and will correspond to the number of birds.

Where to begin?

In order to make a feeder with cutouts or holes, you will need the following PVC parts and accessories:

2 PVC pipes. 60 cm and 80-150 cm with a diameter of 110-150 mm.
Knee. Accessory connecting pipes at right angles.
2 plugs according to the diameter of the pipe.
Tools.

For a feeder with a tee you should purchase:

A vertical hopper feeder will require fewer materials:

1 pipe up to 150 cm long.
1 corner at 45 degrees.
1 corner per 90 degrees.
Stub.

How to do it yourself?

The shape of the feeder is similar to the Latin letter L. The vertical pipe serves as a hopper for loading feed. The horizontal pipe will be the feeding place:

On a pipe 80 cm long, mark the centers of the holes.
We draw holes D=70 mm. Leave the distance between the edges of the holes 70 mm. The holes can be in two rows.
Using an electric drill with a circular bit, we make holes in the pipe.
We process the holes with a file so that the chickens do not cut themselves on the burrs.
We put a plug on one side of the pipe, and an elbow on the other side.
We thread a vertical pipe into the elbow.
We attach the structure to the wall.

With slots

Watch a video about making a chicken feeder from a PVC pipe with slots:

How to construct a feeder from a plastic pipe

Feeding birds is an important process that ensures their health and productivity. For convenient and economical feeding, you can make feeders from plastic pipes for chickens with your own hands.

Traditional bowls and troughs for feeding livestock are extremely ineffective. Chickens love to rake up food, causing large amounts of it to end up on the ground. Open bowls also easily collect litter and feces from other chickens, not to mention the fuss the birds create.

It is very easy to organize devices for feeding chickens with your own hands from materials for plumbing, because it will not take much time, and the necessary tools are available in every home. In addition, it is reliable, since such feeders are durable and can be used as automatic ones.

Tools and materials

To make such a system for birds with your own hands, you will need:

PVC sewer pipe, optimal length 1 meter,
tee with a slope of 45 degrees,
PVC plugs of the same size,
metal saw,
fastener (wire or nails).

Ready-made design for chickens

First you need to cut the surface of the pipes with a saw into three parts: 10 cm, 70 cm and 20 cm.
We put a plug on a plane measuring 20 cm - this will be the basis of the finished structure.
The tee is installed at the top with a side elbow.
A long piece of PVC is placed in this tee. It should be closed with a plug at the opposite end.
A 10 cm piece of pipe is inserted into the hole on the side.
A product made by hand is considered finished. At both ends (top and bottom) it is fixed to the wall of the chicken coop. It will be more convenient if you attach it to a block or metal mesh.
The feeder is filled with loose food.

When the chickens eat some of the feed from the bent knee, it automatically fills with the weight of the feed. Poultry will peck food through the opening of the side tee. You need to close the top of the feeder at night to prevent debris or dust from getting into it.

Complete power supply system

The disadvantages of such a feeder include the inability to feed several chickens at once. Food can also spill out here, but in small quantities. In this case, it is convenient to install several such structures or use the second option.

You can make chicken feeders with your own hands from the same material in another way. This option is designed for a larger number of birds, so it is suitable for large farms. Another method of obtaining food is also used here - the feeding holes are located one level lower, which can be convenient for growing birds. In such a system, feed is saved, because birds cannot climb into the container to rake it.

Birds eat from plastic products

Step-by-step instruction

Placing the finished feeder

The structure is attached to a vertical surface using wire, as in the photo. It is wrapped top and bottom to a pole or mesh. The horizontal part of the feeder should be at the bottom, and food should be poured into the hole on top. It will automatically fill the plane below as it is eaten. This type of feeder is also closed at night to keep the food clean.

A DIY pipe product of this type has a slightly bulky appearance, as well as more connecting parts, so it requires a spacious chicken coop. The feed supply will be enough for about a day - this is for 10-15 laying hens. Sometimes the bottom of the structure is not lowered to the floor, but is kept suspended so that the chickens cannot insert their heads completely into the holes. If there are older chickens in the coop, they will be able to use such a system when it is on the floor.

Laying hens peck grains

Thus, using pipes you can make chicken feeders with your own hands. This method will save the farmer time and money on purchasing feed.

DIY chicken feeder made from a pipe: photo and video master class

With the onset of spring and the end of autumn, our family lives in a country house. We grow vegetables, take care of the garden and shrubs, and also keep chickens and rabbits. Chickens lay eggs all season, and rabbits give birth to offspring. Of course, the issue of feeding comes up every day. At first we fed the birds by pouring food into containers. They realized that this was a bad idea: the chickens turned the containers with grain onto the ground, and the remaining grain was eaten by sparrows. This is very expensive, because we buy food, and it’s not cheap at all. The idea came to make a special device that would be stable, protect the grain from the effects of rain and rain, as well as from the encroachment of other birds.

To make a homemade chicken feeder, you needed the following material:

PVC pipes: smaller and larger diameters

several PVC caps

PVC tee

sleeve

hub.

Tools: drill, hole saw.

Connect the pipes in the sequence shown in the photo. Cut off the places marked with a marker with a saw, drill holes with a drill.

Several simple options for constructing a feeder from PVC pipes

Traditional chicken feeders turn out to be very ineffective and impractical in practice, since birds often climb into them, scatter food, litter and end up turning dishes upside down. Poultry farmers have to constantly monitor the condition of their feeders and spend a lot of time cleaning them. Special devices will help get rid of such problems - feeders made from PVC sewer pipes, which you can make yourself. How? Let's consider.

DIY chicken feeder made of PVC pipes

People who raise chickens in rural areas know very well how carelessly they treat the food poured into open feeders; a quarter can simply be scattered around the yard and trampled into the dirt with their paws. Also, if the feeder is in the open air (on the street in the courtyard of the house), then migratory birds often fly up to eat)) Rodents do not disdain chicken feed, they mostly feed on the feeder in the quiet night time, while the chickens are sleeping on the roost) In general, food loss They are quite large, sometimes even half of them will go to nowhere. For this reason, the author decided to create an economical and very easy-to-make feeder from a plastic bucket and PVC pipes (corners).

The principle is as follows: we take a plastic bucket and drill holes in the side of it, where polypropylene corners are then inserted; they should be located at a distance of 2-3 cm from the bottom. That is, when the bucket is completely filled with food, it will slowly settle as it is consumed by his chickens, “Everything is as simple as daylight.” You can also optionally make a viewing window, so you can see the level of filling of the bucket with food when the lid is closed.

So, let's look at what exactly the author will need to create a chicken feeder from PVC pipes?

1. plastic bucket 10-15 l

2. polypropylene corners 70 mm

1. drill with 70 mm core drill

2. hot glue gun

4. sealant gun

5. stationery knife

Step-by-step instructions for making a chicken feeder from PVC pipes and a plastic bucket with your own hands.

As already mentioned above, the loading hopper is a regular plastic bucket, in this case 10 liters and three corners on the sides to get the chicken head inside the feeder) You can also use a larger container, for example a 20 liter bucket or a barrel. If you need a long-lasting feeder so that you can fill it with food once and forget it for a week, then it is rational to use a plastic barrel with a capacity of 40-50 liters.

Next, you should try on the corner to the wall of the bucket and trace the circle with a marker. Attention Important! The corner should be located 2-3 cm from the bottom of the bucket, so that as the feed decreases, it is supplied to the feeding area.

Then a hole is drilled using a drill and a 70 mm crown, a PVC corner is inserted into the hole made and fixed with hot glue, and for greater reliability, you can also apply sealant.

In order to visually control the level of feed in the feeder without opening the lid, you should make an inspection window in the wall of the bucket. Everything is done extremely simply, namely, using a ruler and a marker, markings are made in the form of a strip 2-3 cm wide, and then cut along the contour with a stationery knife. After which you will need transparent plastic, which can be taken from a regular plastic bottle, we also cut out a strip but in size it should be 1-1.5 cm larger in length and width. We apply it, drill holes and rivet it, go through the edges with hot glue, and then also with sealant.

Now the chicken feeder itself is ready, pour in the feed.

As you can see, the feeder made from a plastic bucket and polypropylene corners turned out to be as closed as possible and the chickens will no longer scatter their food, grain losses will be sharply reduced. Birds will also stop feeding and feeding.

The materials for production are budget-friendly and publicly available, step-by-step instructions are provided to you, so let’s take it and do it. Be brave, friends!

Advantages: minimal feed loss, lightness and mobility, large bunker volume.

Disadvantages: when the feed is used up, the weight of the feeder will decrease and the chicken may turn it over; it is necessary to modify it and make a stable stand.

Watch the video: Bird feeder and waterer made from a plumbing pipe (January 2020).

ATTENTION: The solution to the problem of scattering feed can be to purchase or make a specialized feeder for poultry.

The bin must be tightly closed to prevent the chickens from getting to the feed and eating it all at once or scattering it around the coop.

Having a farmer does not need to monitor feeding time and go to the chicken coop 3-4 times a day to add a new portion.

Kinds

Feeders are divided according to the method of feeding:

Manufacturing requirements

The feeder should hold enough food to provide enough food for all the birds on the farm. When making a tray feeder, plan the length so that each chicken has 10-15 cm. For chickens, half that amount. There must be an approach to the feeders from any side so that the weaker ones are not pushed aside and are not left without food.
The feeder must have certain restrictions so that chickens do not have the opportunity to enter the bunker and scatter and dirty the feed.
It should be mobile, easy to fill, disassemble and clean.

Do-it-yourself feeders are made from plastic buckets and bottles, wood and iron(how, including from a plastic 5 liter bottle?). But the most inexpensive, easy to use and durable feeders are made from plastic PVC or sewer pipes.

Product Description

Advantages:

A plastic pipe feeder is the most reliable of all. It is attached to the wall and the chickens, in the process of feeding and searching for food, cannot turn it over and scatter the grain. Grain is consumed more economically.
One feeder made of pipes is enough for 20 chickens.
The longer the pipe, the more feed can be loaded there. Typically, this design can hold up to 10 kg of dry food and there will be no need to run to the chicken coop several times a day.
Plastic has no limitation on service life. The product is made in a couple of hours and can last for many decades.
Plastic pipes are very inexpensive and are available at any hardware store.

IMPORTANT: Disadvantages of pipe feeders: the structure is easy to disassemble, but long pipes are difficult to wash under the tap and disinfect inside.

Photo

If you are concerned about the question of how to make a feeder with your own hands from polypropylene, plastic and other types of pipes, then you can see the photo:

Can I buy it in stores?

The selection of feeders in stores ranges from the simplest to high-tech devices with a timer and a feed scattering function.

In stores you can find feeders completely ready for installation and use. They immediately have a food container and a tray.

ADVICE: Or you can only purchase a tray divided into sections to which you will need to adapt a bottle or jar. They cost about 100 rubles. and are suitable for farms with a small number of chickens.

It’s even better to make a feeder yourself from scrap materials.. This will cost much less and will correspond to the number of birds.

Where to begin?

In order to make a feeder with cutouts or holes, you will need the following PVC parts and accessories:

2 PVC pipes. 60 cm and 80-150 cm with a diameter of 110-150 mm.
Knee. Accessory connecting pipes at right angles.
2 plugs according to the diameter of the pipe.
Tools.

For a feeder with a tee you should purchase:

A vertical hopper feeder will require fewer materials:

1 pipe up to 150 cm long.
1 corner at 45 degrees.
1 corner per 90 degrees.
Stub.

Tools you'll need

Grinder or hacksaw for cutting pipes.
Electric drill with wood drill and bit with a diameter of 70 mm.
Jigsaw.
File.
Marker, pencil, long ruler.

Material prices

PVC pipe D=110 mm – 160 RUR/m.
Tee D = 11 mm - 245 rub.
Cap - 55 rub.
Knee-50 rub.
Clamps for fastening to the wall for 40-50 rubles.

How to do it yourself?

The shape of the feeder is similar to the Latin letter L. The vertical pipe serves as a hopper for loading feed. The horizontal pipe will be the feeding place:

On a pipe 80 cm long, mark the centers of the holes.
We draw holes D=70 mm. Leave the distance between the edges of the holes 70 mm. The holes can be in two rows.
Using an electric drill with a circular bit, we make holes in the pipe.
We process the holes with a file so that the chickens do not cut themselves on the burrs.
We put a plug on one side of the pipe, and an elbow on the other side.
We thread a vertical pipe into the elbow.
We attach the structure to the wall.

With slots

Watch a video about making chickens from a PVC pipe with slots:

With tee

We put a plug on a pipe 20 cm long. This will be the lowest part of the structure.
On the other side, we put on the tee so that the outlet faces up.
We put a short pipe of 10 cm on the tee outlet.
We insert the remaining 150 cm pipe into the upper hole of the tee.
We attach the structure to the wall.

After attaching to the wall, any feeder is immediately ready for use.. The required amount of grain or mixed feed is poured on top and the hole is closed with a plug so that debris does not get into the bunker and the feed does not get wet during rain.

Watch a video about a chicken feeder made of PVC pipes with a tee:

The importance of proper poultry feeding

A feeder made of pipes is very easy to use and saves a lot of time on the farm. But they are designed to use grain and feed.

But dry food alone is not enough to provide adequate nutrition for chickens.:

Increased nutrition in winter and moderate nutrition in summer, vegetables, fruits, herbs and mineral supplements are the basis for good health and high egg production of your pets.

If you find an error, please highlight a piece of text and click Ctrl+Enter.

Classic methods of feeding poultry are often inconvenient and ineffective. A homemade chicken feeder made from a sewer pipe is practical, affordable, easy to make and does not require large material costs.

Hanging feeder

Hanging models of feeders made from PVC sewer pipes are convenient and practical, because... do not allow birds to climb inside the structure and leave garbage and droppings in the feed. They are hung at a certain height, attached to the wall using screws, brackets or other tools.

The simplest design is made from a wide plastic pipe 1 m or more long and has several plugs. There are several stages in making a feeder:

the pipe is cut into pieces (for example, 0.7, 0.2, and 0.1 m);
a plug is installed on one side of the 0.7 m long part;
install a tee and insert a part 0.2 m long into it, its opposite side is also equipped with a plug;
a part 0.1 m long is also inserted into the tee;
holes are made in the pipes for the feed mixture and the structure is suspended at the required height.

This hanging feeder for chickens made of PVC pipe is convenient for feeding poultry kept in large quantities; it protects the feed mixture from debris and does not injure the livestock.

Wall feeder

The wall-mounted poultry feeding device is also effective and practical in use; additional brackets are required to make it. It consists of polyvinyl chloride pipes with a diameter of 15 cm or more, lengths of 0.1 and 0.2 m, 2 plugs and a tee.

Manufacturing procedure:

The PVC pipe is cut into pieces of 0.1 and 0.2 m;
using a tee, the parts are connected, the smaller of them will act as a tray for the feed mixture, and plugs are installed at the ends of the larger one;
The structure is fixed on brackets to the wall so that the long part is directed upward.

The wall structure is also used as a drinking bowl.

The practicality of using such a product is similar to a hanging PVC feeder, but this design is intended for a small number of birds: only 2 chickens can feed from it at a time.

Floor feeder

Advantages of a floor-mounted poultry feeding system:

it is mobile and can be installed anywhere;
functional and capable of serving up to 10 heads simultaneously;
easy to make.

However, this design is open to debris and therefore requires frequent replacement of the feed mixture. Take 2 plastic pipes of 0.4 and 0.6 m each, 2 plugs and a sewer elbow.

The length of the components varies depending on the number of chickens kept in the house.

DIY manufacturing technology:

holes with a diameter of 7 cm or more are drilled along the entire length of the 0.6 m part;
one side needs to be plugged, an elbow from the sewerage system is installed on the second;
a 0.4 m section is attached to the knee, with the help of which the feed mixture will be supplied;
the part with drilled holes is placed in a horizontal position, secured in a certain place.

Design Features

When choosing a design for feeding chickens, there are some points to consider.

July 22, 2016
Specialization: facade finishing, interior finishing, construction of summer houses, garages. Experience of an amateur gardener and gardener. We also have experience in repairing cars and motorcycles. Hobbies: playing the guitar and many other things that I don’t have time for :)

If you decide to raise chickens, one of the main tasks that you need to solve is feeding them. If you use ordinary dishes for this, for example, a trough, then you will have to constantly add grain, since the chickens will quickly eat it and scatter it around the chicken coop. Below I will tell you how to make a feeder from a sewer pipe without much time and money.

It should be noted that resourceful farmers have come up with many options for making feeders from various scrap materials. In particular, there are several types of structures made from PVC sewer pipes. Next, let's look at a few simple, and at the same time, the most interesting options:

Option 1: vertical feeder

Materials

So, to make a vertical feeder with your own hands, you need to prepare the following materials:

In addition, you will need a tool for cutting plastic. For these purposes, you can use a hacksaw for metal.

Manufacturing

As mentioned above, the manufacturing instructions are extremely simple:

first of all you need to take a pipe one meter long and cut it into three parts– 70, 20, and 10 cm;
then we put a plug on a piece 20 cm long from below. The resulting part is the basis of the design;
a tee should be placed on top of this section so that the side knee is directed upward;
insert a 20 cm long piece into the side knee;
Next, you need to put the longest part of the structure on the tee. In this case, the second plug is used as its cover.

This completes the manufacturing process. Now all that remains is to securely fix the product, for example, you can attach it with clamps to a pole or mesh. At the same time, chickens will peck grain from the side hole.

If you make a metal coil of small diameter, you can make a moonshine still from a sewer pipe.

The feed poured into such a structure is enough for fifteen to twenty broilers or thirty laying hens for at least a day. At night, the top of the feeder should be covered with a lid to prevent debris from falling there.

Option 2: horizontal feeder

Materials

In order for chickens to feel good in the chicken coop, it is necessary to provide them not only with food, but also with a flow of fresh air.
To do this, you can make ventilation ducts from sewer pipes with a diameter of 50 mm.

In addition to a hacksaw, you will need a drill and a jigsaw.

Manufacturing

This design is manufactured in the following sequence:

The pipe must first be cut into two equal parts;
Next, you need to make holes in one of the scraps through which birds will peck food. To do this, you need to mark their location, and then drill holes with a drill. Then the holes need to be widened by cutting them out with a jigsaw.

Of course, this work can be simplified by cutting off part of the upper wall, however, in this case there is a risk that chickens will sit on the structure and scatter grain;

on one side you need to put a plug on the part with holes, and on the other - an elbow and a vertical cylinder. This structure can be secured with clamps to the chicken coop. If necessary, use another elbow to extend the grain receiver beyond the fence, as shown in the photo.

Horizontal sewer pipes can also be used to create a hydroponic system for growing plants. To do this, you need to make holes in them, as in the photo.

The operating principle of this feeder is similar to the previous one, and it is designed for the same number of birds.

Option 3: hopper type feeder

Materials

Finally, let’s look at how a bunker feeder is made. It is perfect for broilers over two weeks old. To make it we will need the following materials:

Manufacturing

The manufacturing process for this design looks like this:

first of all you need to fix a pipe with a diameter of 200 mm on a sheet of plywood. To do this, you can use two metal corners and bolts or screws. The corners must be placed opposite each other. Mounting angles and screws are used in the photo;

Now you need to take a narrow pipe and make a longitudinal cut about 10-15 centimeters long from the end in the center;
then you need to retreat a distance equal to the length of the cut from the edge and make a transverse cut so that it meets the longitudinal one. As a result, half of the wall at the bottom of the part will be cut off;

then the narrow cylinder with the cut side needs to be inserted into the wide one. In this case, the parts must be connected to each other using self-tapping screws or bolts;
after this, you should cut off the bottom of the canister, and put a thin pipe on it with the neck. To ensure that the canister fits tightly, you can use electrical tape or a rubber seal.

This completes the work. The only thing to prevent the chickens from turning it over is to make a hole in the upper part of the canister, thread a rope through it, and tie it to a nail in the wall near which the feeder will stand.

A six-liter bunker is usually enough for thirty broilers for a day. This way, you only have to pour grain into the canister once a day.

Finally, I note that the advantage of feeders is not only that it simplifies the process of feeding chickens, but also that they get used to stable feeding, as a result of which they stop crowding around food and knocking each other down. Very quickly after installing such a structure, they stop fighting for food and come up one at a time.

Conclusion

Making a feeder from plastic pipes, as you have seen, is not at all difficult. Also in this article I wanted to show that this material can be found in many other applications in the household. Some craftsmen even make a cyclone from sewer pipes to collect debris and dust, so you shouldn’t throw away the ones left after repairs.

You will find more information in the video in this article. If some aspects of making the feeder are not completely clear to you or you have other questions, ask them in the comments, and I will be happy to answer you.

July 22, 2016

If you want to express gratitude, add a clarification or objection, or ask the author something - add a comment or say thank you!

A feeder is a device used to feed domestic animals and birds. It is an open container installed or suspended in a suitable place. Different types of feeders may differ in design parameters and intended purpose.

Peculiarities

To feed poultry (chickens or broiler chickens), an oblong-shaped feeder is used. This configuration makes it possible to feed a large number of chickens at the same time. The development and availability of modern technologies allows you to design chicken feeders with your own hands. In this case, plastic sewer pipes with various parameters are used as the main material. Devices for feeding chickens made from PVC pipes have a number of features. Among them are:

low production cost;
simplicity of manufacturing technology;
multifunctionality;
practicality.

The materials used to make a homemade feeder do not fall into the category of budget products, however, their total cost is significantly lower than the cost of a factory feeder. With proper calculations and detailed drawings, you can achieve a significant reduction in the cost of all necessary materials. Its manufacture does not require the use of technically complex tools and devices. The following can be used as a basic toolkit:

screwdriver with drills;
hammer;
hacksaw for wood or metal;
circular saw attachment (if necessary);
measuring instruments (tape measure or ruler);
other related tools.

Making a feeder according to your own drawings will make it as effective as possible. Its design can include various characteristics that help simplify the feeding process or make it semi-automatic. Such a feeder can be adapted to the characteristics of the room or pen in which it will be installed.

The plastic from which the pipes that form the basis of the structure are made is not subject to corrosion and rotting processes, is not toxic and does not emit harmful substances. This fact puts the chicken feeder made of polypropylene pipes on a par with other highly practical devices.

Kinds

Tubular chicken feeders can be of several types:

horizontal;
vertical;
open;
closed.

Horizontal feeder - a pipe mounted horizontally on stands. In its upper part, holes are cut through which feeding occurs. One end of the pipe must be plugged. At the other edge, which is equipped with a special socket, a 45-degree angle made of a pipe of the same diameter as the horizontal pipe is installed. In some cases, both ends of the pipe are plugged. The feeder is filled through the holes intended directly for feeding.

A vertical feeder is a modification of a horizontal one, installed in a vertical position. The edge that the 45 degree angle was inserted into should be on the bottom, and the edge that was capped should be on the top. Feed is supplied through the top edge. The length of the tubular trunk of a vertical feeder determines the amount of feed that will be supplied to the birds during the day.

Horizontal and vertical feeders can be open and closed type. The first type involves chickens consuming feed from one enlarged hole. The second type involves the consumption of feed by each chicken from an individual hole.

Manufacturing

Horizontal feeder

To make your own horizontal chicken feeder, you will need to prepare plastic sewer pipes, wooden blanks for assembling support elements and various fastening devices. The length of the main horizontal trunk of the feeder is determined by the number of birds making up the chicken population. The more chickens, the longer the feeder. Exceeding the length of 2 meters is not recommended. If necessary, you can construct several feeders.

The diameter of the pipe is selected taking into account the characteristics of the livestock. The volume of feed that will be supplied depends on this value. The larger the population, the larger the diameter required. In addition to the diameter, it is important to pay attention to the thickness of the pipe walls. It is recommended to select pipes with maximum wall thickness parameters. This will prevent destructive damage that may occur during operation. Holes are made in the side of the pipe through which feeding will take place. This operation can be carried out in several ways.

Use a circular saw attachment for a drill or screwdriver. The diameter of the nozzle should be maximum. Holes are cut along the tube in a checkerboard pattern. This arrangement of holes will allow the pipe surface to be used as efficiently as possible for its own purposes.
Use a hacksaw for wood, metal or an angle grinder. In this case, the holes will be square or rectangular, which does not in any way affect the efficiency of the feeding process.

It is not recommended to cut out the entire side of the pipe - create one large hole. Over time, the weight of the food may cause the plastic to burst. It is better to leave a distance between the holes, which will serve as connecting jumpers. Next, cap one edge and insert a 45-degree tubular corner into the other. To increase the volume of feed stored in the feeder, you can replace this angle by 90 degrees and vertically insert a piece of pipe into it.

In this case, the feed poured through the vertical section will accumulate inside it and gradually be fed into the horizontal part of the feeder as the chickens eat it. The resulting structure must be installed on wooden legs-stands, attached to the wall of the utility room or to another suitable surface.

Vertical feeder

This type of feeder requires the presence of fastening devices that would hold it on a wall or some kind of vertical stand. A plastic pipe of the appropriate diameter is attached to the selected surface. Perforated tape and self-tapping screws can be used as fastenings. Any other fasteners may be used.

The length of the tube determines the volume of feed that needs to be stored inside the feeder for a certain period of time. It is not recommended to use a piece of pipe whose length would exceed 1.5 meters. Exceeding this value will create difficulties when filling the feeder with food. Corners of the appropriate diameter are placed at the bottom edge. The degree of angle of these components is determined by the design features of a particular product.

The best option is to use two transition angles: 90 and 45 degrees.. This allows you to arrange the outlet in the most convenient position for chickens. The upper edge of the pipe is covered with a special plug, in the surface of which several holes are made. They are designed to allow air to pass through, which prevents the formation of a vacuum inside the feeder barrel and deterioration of the feed material in a closed space.

Bulk feed is fed into the feeder through the top hole in the pipe. Before filling it, it is necessary to plug the lower outlet to eliminate the flow factor. After filling the feeder barrel, the bottom plug is carefully removed.