This time we will be making simple leather bracers.
Rice. 1. Like this
1. To begin, we cut out two parts from a dense and thick piece of leather:
Rice. 2.
We cut it with a regular construction knife. Mine has a blade width of 18 mm. In principle, this is enough. But if you find a knife with an even larger blade, then it will be easier for you to work with it.
2. Next, as in, soak these parts in warm (~40 degrees) water for 15-20 minutes. Then we give them a shape and secure it in any way convenient for you (I simply tied each piece with ribbons on both sides). Let the skin dry on its own, which usually takes about a day.
I didn’t wait a day until the skin was completely dry, and started working with the bracers after about 15 hours. They were a little damp, but in some ways it was even more comfortable.
3. Using a special punch, we make holes for lacing and for rivets (they will be used as a small decoration).
Rice. 3. The photo shows the tools used to make these holes: a punch with different attachments and a rubber mallet
4. To make the edges of the workpiece smoother, you need to burn them:
Rice. 4.
Then wipe vigorously with a dry, hard cloth (at the same time we also use it as sandpaper).
Rice. 5. Cut the lace
6. Now all that remains is to strengthen the holes in the bracers with eyelets (you can also use blocks, but the eyelets are more reliable due to the metal gasket on the inside) and attach rivets. We install the rivets with a regular mallet, and the eyelets or blocks with special pliers. I have 6mm pliers. Blocks of a different size will no longer fit them, so if you are planning to buy these, first think about what diameter you need.
7. Thread the cord into the holes and you're done! These are the bracers we got:
Rice. 6. 
Rice. 7. 
Rice. 8. 
Rice. 9. 
Rice. 10.
Handcuffs are quite practical and reliable! We all certainly know the purpose of this item! And, of course, there is a huge difference between how some scoundrel is cuffed in the next detective series and when handcuffs are put on you!
But for this to happen, you don’t have to be a bad person who commits any illegal acts! No, there are a lot of dangers in the modern world (and it may not even be a law enforcement officer who shackles you), and therefore even the most ordinary person will find it useful to know how to remove handcuffs without a key, especially if your life is in real danger! Our article will help you figure this out!
And first of all, you should understand the structure of handcuffs and the principle of their operation! For these purposes, the best thing for us is a video that shows everything perfectly! However, let us immediately note that although the principle of all handcuffs is similar, depending on the model, there may be various design features that complicate their opening and tearing (more on that below)!
As was said, the video above perfectly shows the principle of operation of handcuffs; for those for whom the video does not work or requires explanation, I will try to explain in my own words! From the video we see that instant locking of the handcuffs occurs due to the presence of teeth located on the movable part of the handcuffs (on the “bracelets”) and opposite teeth on the locking mechanism. It is these opposite teeth that lock the mechanism, which allows the “bracelets” of the handcuffs to move only forward! This is very convenient for quickly shackling a person.
It is also clearly visible that the handcuff key does not have any tricky grooves, but is made very simply. The shape of the key is very standard and has mainly a hole in the middle and one pressing element, which, moving clockwise, presses on a plate with opposite teeth, lowering it, which allows you to open the handcuffs (move the “bracelets” back)! To imitate a key (make a master key), it is best to take a hairpin! If you have a hairpin (or something similar) on hand, you can proceed in two ways:
1. Bend the pin in the form of a club and insert it into the slot for the key, move it clockwise (you just need to pick up the mechanism and lower the plate with teeth) and then carefully open the “bracelet” (you need to hold the pin while it presses on the plate with teeth ).
2. There is no need to bend anything, there is a slot on the side of the handcuffs into which you need to insert a pin, which will also help open the handcuffs! (watch the video)
Another important point is also clearly visible! For more reliable protection, the handcuffs are equipped with a special “pin”, which moves the bottom plate of the locking mechanism to a position in which it becomes much more difficult to open them without a key (and absolutely impossible, unless you know some tricks, as I understand it).
In this position, it is no longer possible to open the handcuffs with the key simply by turning it to the right, because the “pin” entering the handcuffs blocks the opening mechanism, so that in order to open the handcuffs you will first have to put the pin in place. To do this, it is enough to first turn the key to the left to move the plate to its original position and thereby return the “pin” to its original position, and only then turn the key to the right to open the “bracelets”. We also see that when blocking with a “pin”, it will not be possible to squeeze out this same “pin” using a master key (by pressing on the bottom plate, turning the master key to the left), but you can try to resort to some trick:
3. To return the “pin” to its original position without a key, you need to hit the handcuffs well from the side in the area of the “pin” (delivering a sharp, sensitive blow so that the “pin” literally flies into place. How this method works can be seen in the video below:
4. In addition, the handcuffs can be broken!!! Everything here seems to be simple, the main thing is to take it at a break, that is, the handcuffs are not on a rigid coupling (you can’t break them on a rigid one! Like some particularly strong models), you need to bend them in the coupling itself so that a support for the lever appears, then twist it with your hands trying to break it . You need to act exclusively on the break! If the model of handcuffs is suitable and you are not the worst hole or girl, everything should work out for you, and the handcuffs may break even faster than if you tried to open them with a hairpin! However, there is a “but” here too! This trick won't work if your hands are cuffed behind your back!
© SURVIVE.RU
Post Views: 19,304
Before reading a fascinating and no less useful story, it is imperative to decide on the following: if for some reason you fall into the hands of the police, then completely eradicate thoughts of how to open handcuffs without a key, because the forces of law and order are not to be trifled with, a priori! This article is aimed at overcoming the actions of not quite normal members of society who have handcuffed you and are planning to do something terrible. The information presented will benefit everyone without exception, even girls.
How to get rid of handcuffs?
Did the New Year holidays end in a funny way, if only because you found yourself handcuffed to a radiator? This problem can be solved quite quickly and efficiently if you know some tricks that explain how to open handcuffs without a key at home.
For example, for almost any actor this task will be extremely easy, because he knows that to get rid of the shackles he just needs to find a wire, move the handcuff lock for a few seconds - and that’s it! This means that it would be advisable to do the same, diving into the search for the same wire or an ordinary paper clip. It’s great if you can call someone for help, because another person can not only bring a tool to get rid of handcuffs, but also help solve the problem in practical terms.
It is important to note that this information was obtained as a result of an experiment discussed in the next chapter and, as it turned out, completely answering the question of how to open handcuffs without the BRS-2 key.
Experimental confirmation!
In the experiment, which was carried out to test the effectiveness of the scheme, the specialized police mechanism BRS-2 was used. So, it was put on a person’s hands, after which the experimenters went in search of paper clips. As it turned out during the operation, it is important not to miss three main points:
- Before you open handcuffs without a key with a paperclip, you should first get your bearings. For example, the BRS-2 has a pass-through lock, which allows you to insert the key from any side. And it opens by moving towards the far edge of the lock block.
- It should be noted that a massive paperclip will be an absolute advantage, because it bends less and has little chance of breaking. You should form one end of it like a key tongue, then insert it and twist it in the desired direction. Of course, you will need to try for 10-15 minutes, nevertheless, freedom is close, and in the end everything will work out!
- Only a thin paperclip was found? It’s great, because with its help you can create a real duplicate of the keys! BRS-2 has two plates that fix the teeth of the bracelet, which justifies the presence of a double tongue on the key.
Secrets of the lock blocker and some interesting nuances
The most common in the Russian Federation are BRS-1 and BRS-2. In addition, their locks can be endowed with both simple and complex shapes. You need to know that most handcuffs have a specialized lock to control the degree of tightening, which serves as a lock blocker.
So, if the lock is activated (the lever is deep in the hole), first you need to open it, and then start working directly on the lock. The lock opens with one movement in the opposite direction. In addition, there are known models of handcuffs with rigid coupling of bracelets instead of chains. In such cases, the owner’s hands are given the bare minimum of freedom. But it is almost impossible to open these handcuffs, but with the maximum amount of effort, anything is possible in this world!
It is important to note that the process of solving the problem of how to open handcuffs without a key is divided into several stages, regardless of the chosen tool for eliminating the “shackles”. In addition, there is a classification of methods for getting rid of handcuffs depending on whether the owner is a beginner, an amateur, or maybe even a pro.
Preparatory stage
How to open handcuffs without the BR S key? Let's look at this:
- First you need to ensure that your hands are in front. It should be noted that this stage is not as difficult as it seems at first glance, even if you have never done gymnastics or yoga.
- The second operation, naturally, is to find a tool for picking the lock. Above we discussed in detail an experiment with a paper clip, which can easily be replaced with wire, a pin, or a watch tie. In addition, the most savvy people managed to open the lock of handcuffs even with ordinary matches. However, if possible, it would be advisable to find an extremely thin and rigid tool, which will help to fully grasp the lock and avoid breaking the tool at hand.
- The third operation is to make a mark of three to four millimeters from the end, for example, of a wire, after which it is necessary to bend it at a right angle. The ideal material, of course, is platinum, because it has a minimal degree of deformation when interacting with the lock, because the force is directed along the edge.
Classification of lock opening methods
The easiest way to solve the problem of how to open handcuffs without a key, if you are new to this matter, are bracelets without an active latch, which, as a rule, is located on the plane of the handcuffs below the lock. As noted above, the exception of the lever being recessed into the hole indicates the inactivity of the latch. In addition, some models of handcuffs do not contain it at all.
In any case, the process diagram is as follows: the teeth of the moving part contact the grip, as a result of which the pawl falls and the handcuffs close. The key lifts it and the mechanism opens. This means that it is possible to fake the pawl manually, by moving the wire between the teeth and then grabbing it.
If there is a latch, it will not be so easy for beginners to disable it, but amateurs will carry out this operation without much difficulty by turning the tool counterclockwise. It is important to note that extreme care must be taken when turning to prevent the lock from re-engaging. Only professionals in this matter will be able to open the BRS-2 handcuffs, because their lock has a particularly complex structure. The corresponding process is described above.
How to open handcuffs without a key? Actual problems
As a rule, in the process of getting rid of handcuffs, problems arise associated either with the inability to find the necessary tool, or with going inside. It is important to note that the latter is not relevant for the BRS-2 model, since it is endowed with its through type.
In addition, there are BOS handcuffs, which have a distinctive feature (i.e., they do not have a chain between the bracelets). In this case, the owner’s hands become numb and very painful in a short period of time due to limited movement. So, even if you have a key in your hands, it is not always possible to open the lock. There is only one consolation: such handcuffs are not widely used in society, probably because of their extreme cruelty.
In the opening diagram of the BOS model, the blocker is marked with a red rectangle, and the directions of influence are marked with green arrows. The plate to be affected is indicated by a short red line. When it is in the place marked with a dotted line, the latch is considered open.
When summing up such an extraordinary story, it is important to recall a very standard, but very effective truth: the best method of getting rid of handcuffs is to prevent them from being put on.
Hello to all fans BDSM and iron toys. Before making shackles, think about whether it might be better to buy them in sex shops?
I’ll try to explain now how to make shackles. In principle, this is not difficult. You will need:
1. Bench vice.
2. Hammer.
3. Pliers.
4. Hacksaw for metal.
5. A metal brush for cleaning surfaces - or a wire wheel for polishing with a drill.
6. Files - 3 pieces: flat (rough and fine), and round - for boring holes.
7. Electric drill and drill (it’s good if you have a machine, but you can do it with a vice).
8. Taps for cutting internal threads (if you want to make shackles on screws)
9. 5 bolts with nuts.
10. Sanding paper and sandpaper (for polishing). If the grinding wheel is even better.
As the starting material for the shackles, we take a strip of iron 3.5 cm wide - hoops for small barrels are made from these. Go to any metal market - they cost pennies there. We cut off two pieces and make cuts in them with a hacksaw, like this:
Now the second stage. We bend all three “tongues” into a semicircle - this will be the blank. In profile, the strip of iron will then look like this - (A). From the same wire we bend a “triangle” to the size of the shackle bracelet - this will be a hinge and at the same time an eyelet and a fastening for the chain (B). It should be slightly wider than the bracelet itself, since it will “encompass” it from the outside. It is better to bend it immediately around a piece of thick iron wire that you find - this will be the axis of the future hinge, around which the detachable halves of the bracelet (B) will rotate, opening.
At this stage, it is best to thoroughly clean everything from rust with a brush, polish it with a file and sandpaper, remove burrs, and smooth the edges. In general, it’s good to make shackles from stainless steel, but it’s more difficult to process. Then we begin to put everything together using a vice, a hammer and a handy anvil. If the dimensions are kept exactly, only a small adjustment with a file will be required (this can be easily checked at stage “A”). We assemble right around the base of the wire triangle. We bend the ears into loops and get an assembled hinge (B and D). The junction of the triangle will be hidden under a strip of iron - the result will be a strong structure (D). There is no need for welding or soldering - it is quite difficult to break it, even if you want to, bend it too, believe our experience J.
So, the blanks for the bracelet shackles have been assembled. Here they are - two hand ones, two foot ones, plus a collar. Here they are still unpolished, but already with rings, where the chains will then be attached... In principle, if you are not too lazy to tinker, you can immediately connect the chains during the process of assembling the bracelet, through the connector - it will be more difficult, but as a result you will get shackles that are almost real, where there will be no cuts or connectors. But then try to guess the length of the chains in advance.
Now we take each workpiece and begin to bend it so that it takes the shape of a semi-ellipse. Already at this stage, you need to mark the bracelet - measure a strip along the circumference of your wrist (ankle, neck), so that the hinge falls in the middle of the length. (When you bend, do not fall into the trap of a common misconception - an arm or leg only appears round at the wrist and ankle, but in fact it is oval in cross-section!) Take a pipe of a suitable diameter or a block of hard wood and bend around it - it will be easier and faster. Then bend it into an oval. Add 2-3 mm in length. Moreover, when bending, an error may occur, the internal diameter of the ellipse will decrease slightly. Remember that you need to leave some for the “ears” that will connect the halves when forging, and these “ears” must remain straight... It all looks like this:
Or like this. Isn't that better? J:
Now we begin to form the bracelet itself. We clamp such a “heart” in a vice, then, according to the marks made in advance, we make two folds and get this squiggle:
This is if you open it and put it on its “legs”. And if you fold it in a normal way, the shackle bracelet will turn out almost like a real one. Here, look:
Well, in general, that’s almost all. All that remains is to drill holes, take taps, cut a thread in one half of the bracelet and screw a bolt into it, then cut off all the excess from the “lugs” so that they become semicircular, and sand the edges with a file and sandpaper. And we get a finished product made by ourselves:
For those who are picking up a tap for the first time, a couple of smart tips:
1) The bracelet must be clamped in a vice, and the surface of the “ears” must be located horizontally, parallel to the plane of the workbench;
2) The diameter of the drill must be equal to the diameter of the tap barrel, and not the diameter of its thread;
3) Be sure to use a special wrench. When cutting threads, use a rough tap first, then a finishing tap (they are always sold in pairs, so you don't get confused). Do not unscrew the tap back - it is best to make the pass through;
3) And don’t rush - “The service of the muses does not tolerate fuss” J . Rotate the gate slowly, and when cutting, drop a drop of spindle or transformer oil onto the working surface of the tap, otherwise you risk splitting the tap lengthwise - hardened steel is very hard, but brittle.
The screwed bolt in its half of the bracelet sits tightly and does not fall out (you can even shorten it a little so that the tip does not stick out). As you put it on, the nut is screwed on. It’s almost impossible to remove shackles without a wrench (especially for a girl), it’s been tested.
Well, where are our pens? J
And this is the entire product assembled (click to enlarge)
See you! Good luck to everyone and sweet dreams! J If we open a normal workshop, you are welcome to place orders.
E-Mail (VORON and TANUKA):
From the Administration. A truly wonderful product and quite affordable. I found out about a year ago - the guys asked for 2500 rubles. per set. But, unfortunately, the workshop has not been opened to this day. We wish our colleagues good luck and hope that the problem will be solved! And orders will definitely appear!
You can order ready-made shackles here www.btoys.ru. Prices are reasonable. Any sizes, types and shapes!