Even a novice master with a simple set of special tools will be able to figure out how to install a sink in the bathroom. A focused person should not have any real difficulties when performing such an operation.

Types of fastening sinks - get acquainted with the options

Manufacturers now produce a wide variety of types of washbasins. They differ from each other not only in their appearance, but also in the method of fastening. From this point of view, shells can be:

1. With a pedestal. They are fixed on brackets or other fasteners. The pedestal of such sinks masks the elements of the sewer system and. You can choose the desired height for installing the washbasin yourself.
2. Invoices. These sinks are always placed on the countertop. It has a relatively small rise above the plane. When installing such plumbing equipment on the countertop, it is necessary to provide a place for mounting the faucet, since, as a rule, there are no holes for it in overhead sinks.
3. Mortise. Washbasins mounted in the countertop. In this case, they are installed above the surface with a 2-3 cm protrusion. The equipment is fixed using special fasteners.
4. With fastening to the wall surface. Such sinks are either screwed or fixed to the wall of the bathroom.
5. Furniture. Equipment that comes complete with a cabinet or a special stand with certain geometric parameters.

Sink in the bathroom

Do-it-yourself installation of different types of washbasins follows approximately the same pattern. But in each case there are also significant nuances. They should be studied if you want the washbasin to be installed in the bathroom once and for centuries.

We are preparing to install new equipment - what needs to be done?

First, you need to stock up on all the tools, without which the installation of new plumbing equipment cannot be completed. You will need: concrete drills, impact drill or hammer drill, silicone-based sealant, adjustable wrench, set of screwdrivers or screwdriver, dowel screws, wrenches, self-tapping screws.

Removing an old sink

Now start removing the old sink. With your own hands, a similar procedure is performed as follows:

1. Shut off the water supply to the house (apartment).
2. Unscrew the fasteners that secure the mixer.
3. Disconnect the water pipe.
4. Remove the mixer.
5. Tighten the nuts at the bottom of the old washbasin.
6. Drain the remaining water from the siphon. Then dismantle it.
7. Disconnect the siphon from the pipe (if you are replacing it with a new device).
8. Remove the sink itself.

When disconnecting a flexible or rigid pipe from the mixer, lower its end into any container. There may be a lot of water left in the liner. It will flood your bathroom if the above precautions are not taken. Also, after disconnecting the siphon, we recommend plugging the drain pipe with a plug of a suitable size or with a regular rag. Then unpleasant odors will not penetrate into the bathroom. The plug or plug should be removed immediately before installing the new siphon.

We install the washbasin on the brackets with our own hands

A sink with a pedestal (a tulip beloved by many domestic consumers) is mounted taking into account the peculiarities of its design. You need to install the equipment leg, faucet and siphon correctly. It should be taken into account that the water drain will be located inside the pedestal. This means that all elements of the sink will have to be insulated and secured very well. This is the only way to protect yourself from leaks and the need for labor-intensive dismantling of the washbasin to eliminate them.

Self-installation of the sink

Tulips are usually mounted on brackets. The procedure for doing the work yourself is as follows: first make markings on the wall, draw a horizontal line 85–90 cm from the floor base, then measure the thickness of the sink from the side adjacent to the wall surface. Now step back down from the first line at a distance equal to the measured thickness, and put a second mark. This line will show exactly where the brackets should be mounted.

After this, measure the width of the washbasin. Mark it with marks on the line where the brackets are located. Drill holes at the marked points. Place dowels into the “holes” made, screw the brackets to them, and install the bowl on the fasteners. Here it is important to achieve maximum tightness of the washbasin to the wall surface. The sink must be truly stable - any swaying or shifting is unacceptable.

Finally, you connect the mixing device with your own hands, and then the drain. All existing joints must be treated with sealant. It is also possible to install the bowl directly on the leg. In this case, the tulip should be placed at some distance from the wall. This DIY installation method is rarely done. It does not provide the required quality of fastening the sink if the work is performed by an inexperienced home craftsman.

Note. The method of installing a tulip on brackets is also suitable for installing hanging bowls. In such cases, the mixer is placed either on the washbasin itself or on the wall above it.

Overhead and mortise bowls – minimum hassle

Such sinks are mounted on various types of countertops and bathroom furniture. They are easy to install on special wood furniture, fiberglass products, brickwork, marble surfaces and artificial stone structures. Almost all overlay bowls are manufactured in a shape that ensures they are securely mounted to a specific solid base.

Example of an overhead bowl

It is very rare that you have to make openings of the required diameter in the tabletop with your own hands. Usually it initially has a hole for mounting the bowl. If there isn't one, you'll need to cut it out yourself. For these purposes, it is best to use an electric jigsaw. If the installation of sinks of the described types is carried out on a surface made of artificial stone or fiberglass, there is no need to treat the joints with moisture-proofing agents or sealant.

But it is correct to additionally waterproof wooden furniture and natural bases . With this treatment they will last much longer, without accidents or leaks. After all these preparations, all you have to do is put the washbasin in the opening that was made (originally available), and then install the siphon, pipes, and mixer. They are carried out similarly to the operations described above (for pedestal sinks).

Sink with cabinet - installation details

It’s not at all difficult to handle such a washbasin, which comes complete with a cabinet, with your own hands. You need to immediately (before installing the sink on the base) connect a corrugated pipe with a siphon and flexible hoses for supplying water to the cabinet. If you try to do such operations after installing the bowl, you will encounter a lot of problems. They are due to the limited space inside the cabinet. It is almost impossible to carry out work on connecting system elements in such cramped conditions.

The second caveat is that in some cases the holes for the siphon pipe and hose outlets available in the cabinet are not suitable for your specific installation conditions. The problem is solved by cutting new openings. Use a circular saw or an electric drill for this. Next, you need to position the cabinet correctly - strictly horizontally. The procedure is elementary. The cabinet has adjustable feet. You need to place a regular building level on the leveling stand. And then carefully twist the legs.

Sink with cabinet

After this, place the bowl in a horizontally aligned cabinet and begin attaching the sink to the wall surface. This can be done in two ways: using sealant (silicone), using anchor screws. Pros advise choosing the first option. The fasteners do not need to be made extremely reliable, since the washbasin stands firmly on the cabinet. All you have to do is fill the space between the wall and the bowl with sealant and wait about 60 minutes for it to dry.

Installing anchor screws will significantly increase the labor costs for fixing the washbasin. And the result from such complex work will be the same as when using sealant. The last step of installation is to connect a siphon to the sewer pipe and a mixer to the water supply. This will complete all work.

Add site to bookmarks

List of required tools and materials:

• adjustable wrench;
• gaskets-washers;
• nuts with flange and different threads;
• welding machine;
• silicone sealant;
• dowels

How to remove an old sink

When it comes to choosing a mixer, it is necessary to take into account the length of the pipe, as well as correctly calculate its location. The crane must be mounted at the required height, not ride on the surface and rotate well.

Before you begin dismantling work in the bathroom or any other work that concerns the water supply, you must turn off the water. Once the lack of water supply has been verified, work can begin.

First you need to unscrew the nut that holds the mixer. Then disconnect the flexible or rigid line. The best option is to place the disconnected pipes in a bucket, as there may be waste remaining in them. Then the mixer can be removed. Next, disconnect the siphon that connects the washbasin to the sewer. You can remove the siphon if you carefully unscrew the lower nuts. Then the washbasin is removed from its mountings and thrown away.

Types of shells

A huge number of models makes it possible to choose a washbasin that will satisfy both aesthetic and functional needs.

When purchasing, be sure to pay attention to the appearance and dimensions of the sink.

Depending on the type of installation and design, there are the following types of washbasins:

• tulip sink;
• sink on brackets;
• on the stand;
• on a pedestal

Installing a tulip washbasin

There are no special differences in the installation of this model. The only feature of this type is the installation of a leg on which the bowl will be lowered. The installation height of the washbasin should correspond to the height of the lower leg. A mixer and siphon are installed together with the washbasin. Special tools are required for their installation.

The peculiarity of this type is that the drain will be located inside the leg. Therefore, all parts must be carefully secured and insulated so that you do not have to repeatedly dismantle the washbasin and constantly fear a flood in the bathroom. Before you start work, you should definitely consult with people who know the rules for installing a washbasin.

How to install a sink on brackets

This is one of the common methods that is quite easy to do on your own. To install such a model in the bathroom, you first need to complete all the finishing work. First of all, you need to make the correct markings and only then start placing the mount.

First you need to draw a horizontal line at the desired height. Basically it is 85 cm from the floor level. Having retreated a distance that will be equal to the thickness of the sink on the side adjacent to the wall, you need to draw a second line. This will become the basis for attaching the brackets. Having measured the width of the sink, you need to attach the brackets to the wall, then put marks for future holes.

Holes are drilled at the points and dowels are installed. The fasteners are screwed onto them and the washbasin is installed. It should not wobble or move. Only after the bowl is firmly and firmly attached to the wall and does not move can the drain and mixer be connected.

Installing a washbasin on a cabinet is considered an alternative to this installation method.

How to install a washbasin on a cabinet

In this situation, the tabletop of the cabinet itself acts as a holder for the bowl. When installing a sink on a cabinet, it is inserted entirely into the hole or installed on top. But in these two cases, the drain is hidden in a cabinet or under a shelf. It is necessary to install the sink on the cabinet according to the method given above. But its advantage is that a huge number of unusual design models have been invented for this method.

These models look like standard washing bowls or have an original shape. Designer sinks are made of spherical or cubic glass. You can decorate such a sink yourself using stones, smalt and anything else that your imagination suggests. Thanks to all this, installing a sink on a cabinet can be done with great pleasure.

Mounting a pedestal sink

In this situation, everything depends only on the type of bowl. In some cases, it is mounted on brackets, and the pedestal serves only a decorative function. In all other situations, the bowl is mounted on a pedestal and it seems that the washbasin is standing on it. In this option, the sink can be placed at a considerable distance from the wall.

If the structure is adjacent to the wall, then first it must be mounted in the intended location, then mark the places to strengthen the bowl. In this case, use bracket reinforcement, which was described above. Rubber washers must be attached to the screws and not tightened very tightly so that the washbasin does not move from its place. If you apply too much force, it will cause cracks in the sink.

When the sink is installed on a semi-pedestal, the outlet socket must be positioned at a distance of 0.5 m from the floor. The washbasin is attached to the wall, and the semi-pedestal is mounted as recommended by the manufacturer.

How to install a siphon correctly

If you install a sealed siphon incorrectly, this can lead to the appearance. It is the siphon that drains the water.

The siphon assembly must be carried out according to the manufacturer's instructions. The product must only be mounted vertically. There is no need to use corrugation in the siphon - it blocks the passage of soapy water and accumulates dirt.

After installing this equipment, you need to fill the sink with water and check the degree of tightness of the connection. If a leak is detected, the product must be thoroughly dried and reassembled, replacing the gaskets and treating the leak area with silicone sealant.

Mixer installation

The installation of the faucet also depends on how practical the washbasin is installed in the bathroom. It is necessary to choose the most practical location of the taps. When it comes to choosing a mixer, it is necessary to take into account the length of the pipe, as well as correctly calculate its location. The crane must be mounted at the required height, not ride on the surface and rotate well.

The line to the mixer should not be long - the excess must be cut off.

First you need to attach it to the taps, and only then to the pipes. You should also check for leaks and, if necessary, seal the material if a leak is detected in the bathroom.

The work of installing taps and sinks does not take much time and can be easily done with your own hands. You just need to follow all the manufacturers' advice, carefully measure distances and remember safety precautions.

Let's look at the step-by-step installation of an undermount sink. Together we will assemble a drainage system under the sink and connect it to the water supply in the bathroom.

Step 1: Installing taps for inlet and mixer

Installing a bathroom sink begins with removing the caps from the water outlets that are located at the outlet from the wall. After this, we screw on the taps for supplying hot and cold water, first wrapping the FUM threaded connection with tape or tow with paste. In order for the faucet to fit tightly to the wall, the seal must cover all the threads. After tightening, the holes in the corner taps for the flexible hose should point upward. Turn the valves as shown in the photo. To save money, you don’t have to make separate taps, but then if a water leak is detected, you will have to turn off the entire water supply, and not just one of the taps.

We put the sink in place, level it and draw the outline with a pencil.

We connect flexible water hoses for hot and cold water to the mixer. As a rule, the standard eyeliner included is short, so you have to buy it separately. When assembling, do not forget to install a gasket and a thin rubber band to prevent water from leaking from the tap. We pass the faucet with the hoses wound through the hole, install a rubber and metal washer alternately on the back side of the sink, screw the pin into the faucet and the nut, and tighten it. Mixer.

Step 2: Attaching the Sink to the Countertop

Next, to install the sink in the bathroom, we coat the entire outer part of the edge of the opening with white silicone sealant, without going beyond the circle outlined in pencil. This way, the silicone will not protrude beyond the sides of the sink and will fix it from the inside, creating a reliable gasket.

After applying the silicone, return the sink to its original place, placing it strictly along the marked line, and press it tightly. Wipe off excess silicone with a damp cloth.

Step 3: Sealing the Sink Joints

Let's start sealing the joints between the sink and the countertop. To do everything as carefully as possible and not to smear the sealant over the entire surface, we tape the circle around the sink and the side of the plumbing with masking tape.

Coat the joint with silicone and smooth the seam with your finger or a plastic spatula.

Remove the tape and carefully remove excess silicone with a damp cloth. The top installation of the inset sink is completed, let's move on.

Step 4: Connecting flexible hoses to the water supply

We have already connected the flexible hoses to the faucet, it's time to connect them to the outdoor water supply. To wrap the faucet, we do not use FUM tape or tow with paste, since there is a sealing rubber inside at the end of each hose. We manually screw the hoses alternately to the cold and hot water taps. Flexible wiring is fully installed.

Step 5: Installation of the bottom drain

Let's start installing the bottom drain. A chrome-plated bottom valve from the German manufacturer Gro Welle was selected for installation. On the side of its neck there is a hole for an overflow. If the water in the sink is higher than the set level, it will flow out through the overflow.

We assemble the system; the opening of the neck and overflow must match.

We place one silicone gasket on top of the neck.

We screw the second silicone gasket from below onto the thread of the nut.

Tighten the connecting nut well using a wrench.

Finally, screw the bottom drain plug into place.

Step 6: Assembling and connecting the siphon

In front of you are the siphon parts, we are assembling the structure.

We connect the glass with the cup holder, not forgetting to put on the sealing gasket. We put the seal on evenly, without distortions, to prevent leakage. We put a union nut and a cone gasket on the pipe connecting the neck, insert the structure into the upper hole of the siphon and tighten it. We connect the corrugation, put on the nut and cone gasket, and tighten it moderately.

We screw the siphon onto the neck nut, not forgetting about the gasket.

We tighten the threaded connections of the siphon, straighten the corrugation as needed and remove its pipe into the sewer drain.

In a modern apartment, a sink is a standard item in any bathroom. Plumbing manufacturers today offer many types of sinks. And although the general installation principles are the same, there are some installation nuances for each of their installation options.

At the final stage of a bathroom renovation, it’s time to install the plumbing. It is important to place it correctly and conveniently. Correct placement of the sink is especially important for small bathrooms. One solution to this problem is to use a wall-mounted sink. Well, when you have everything ready, do not rush to call a plumber. Everyone can install a washbasin on their own. The main thing is not to forget to connect it to the water supply and sewerage at the end of installation.

The better the installation, the longer and better the plumbing equipment will work. The main thing is not to rush, to do everything correctly and “wisely”. In the future, this will allow you to calmly enjoy the fruits of your labors, and not correct your own shortcomings.

Photo of an already installed black sink

Installing a bathroom sink: step-by-step instructions

Let's look at the main types of sinks according to the method of fastening.

• Invoices. Sinks of this type are designed for installation on a countertop with a small protrusion above its surface. Sinks of this type often do not have a hole for the faucet.
• Console (suspended). Bathroom sinks of this type are hung on the wall using a bracket or fasteners. Their installation does not require a cabinet or countertop.
  To cover the sewerage system and water supply, the sink should be installed on pedestals. A pedestal mounted cantilever sink is also called a tulip bathroom sink.
• Mortise. Sinks of this type are cut into the countertop from above or below. In the first case, the sink is mounted on a countertop with a protrusion above the surface of one to three centimeters.
  Be sure to seal the seam. When inserting a sink from below, use L-shaped fasteners. With their help, a mortise bathroom sink is attached to the base from below.
  This method of fastening is more practical: you can collect the splashes in one movement.

Please note that the water from the siphon must be drained. To prevent the smell of sewerage from penetrating into the bathroom, the pipe opening should be plugged with a stopper, a rag or other available means.

Photo of a “Tulip” type sink

Installation of a pedestal sink

Installation of a pedestal bathroom sink depends on the specific model:

Photo of a tulip sink in a bathroom interior

Furniture. This type of sink is usually supplied by a bathroom furniture manufacturer. Install them on a stand or cabinet for a bathroom with a sink of a suitable size. You can install the sink on a regular countertop.

Please note that the types of bathroom sinks determine whether you can do the installation yourself, as some types require time, patience and some professional skills to install.

Photo of an installed wall-mounted sink

Dismantling of old equipment

Installation of new equipment requires dismantling of old equipment. To remove the sink:

• the sink can be mounted on the wall,
• the sink can rest on a pedestal.

Photo of a sink with wall mount

Please note that in this case the sink may be located away from the wall.

1. place the sink in the planned location and mark the mounting points on the wall,
2. drill holes, drive in plugs or dowels,
3. secure the sink with bolts,
4. attach the siphon and install the mixer.
5. connect the sink to the sewer using long pipes,
6. connect the sink to the siphon.
7. secure the sink to the brackets and seal the joints.

Installation of sinks on brackets (console)

The option of attaching a sink to a bathroom using brackets is the most familiar and common.

Photo of a sink on a pedestal

Mounting on brackets

1. Make markings. Draw a horizontal line at a distance of 80-85 centimeters from the floor (this is a standard level). Draw vertical lines across the width of the sink perpendicular to the floor.
2. Try the brackets on the sink, then place them against the wall and mark the location of the holes.
3. Drill holes, hammer in plugs or dowels and screw the brackets.
4. Install the sink, taking into account the features of the model.
5. Connect the siphon.
6. Install the faucet.

Sink in the form of a glass bowl on a pedestal

Please note that after installation the sink should not wobble.

Installation of a sink on a shelf or cabinet (mortise and furniture-mounted)

Installation of the sink on a shelf or cabinet is carried out in the cutout of the tabletop. In this case, how to fix the sink in the bathroom is necessary in advance. The entire sink can be recessed into the cabinet or left standing on the surface.

Photo of a beautiful Tulip type shell

Installing a sink on a shelf or cabinet is the easiest:

1. install the sink into the cutout of the countertop,
2. connect the siphon,
3. install the mixer.

Photo of a sink on a shelf

Please note that the faucet can be mounted directly on the sink or countertop. It can also be placed on a decorative stand.

After installing any type of sink, you must open the water and check the structure for leaks. Don’t forget, proper installation and daily maintenance will increase the life of your sinks.

Photo of a sink with a cabinet

Source: eto-vannaya.ru

Simple instructions for installing a sink on the wall

Before purchasing a new sink for your bathroom, you need to calculate its optimal size and also decide on its placement location. A popular option is to mount the sink on the wall, as this method will save space in the room. If you choose this method, then make sure that the wall on which you are going to mount the washbasin is strong. A plasterboard wall will not support a sink, so it cannot be hung on this type of ceiling.

To build something new, you need to break the old. If you are going to install new plumbing in place of the old one, remove the old sink. Carefully unscrew the faucet. Before dismantling the siphon, the water must be drained from it. Once the faucet and trap are disconnected from the sink, you can remove it.

If you plan to install the washbasin in a different location, you will need to run hot and cold water pipes underneath it.

Built-in sink

The sewer pipe should be placed exactly in the center of the sink. It is very important to install the washbasin at the correct height so that it can be used comfortably by all family members. Typically the height ranges from 80 to 90 cm from the floor. All measurements must be marked on the wall so that it is convenient for you to install plumbing in the future.

Tools and materials

In a hardware store you can find the necessary set of fastening elements for the sink. Since moisture and dampness are eternal companions of the bathroom, you need to choose silicone sealant with special care. There are special sealants on sale that are designed specifically for bathrooms (especially wet areas). If you choose this material correctly, it will not turn black over time.

Several installation methods

The installation method will depend on the sink you purchased. Below we will look at several popular mounting options. Before installation begins, it is necessary to turn off the water in the pipes. And also complete all the preparatory work that we described above.

First you need to note the level of installation of the plumbing fixture. Initially, mark the selected height on the wall. The optimal height is 80-90 cm. In order for the walls of the bowl to withstand the pressure of the brackets, you need to know their thickness. We measure it and transfer it to the existing horizontal line (height). Then we make marks.

The next stage is to mark the markings for attaching the sink to the wall. Turning the bowl over, we mark on the recesses on the reverse side for installing the frame. In this case, you need to level the washbasin using a level. Since this work is quite difficult for one person to do, it is best to involve someone else in this process. Make sure that all your marked lines match.

Photo of a washbasin with a built-in bowl on a cabinet

According to the markings, it is necessary to make a hole for the bracket and washbasin. Then we drive the bushings into the holes; they should be included with the washbasin. We screw the screws into them. And then you can install the support.

The next step is to install and secure the bowl. We place the bowl on the brackets and make marks to secure it, then drill holes along them and install the sink in its place. It is very important to control the depth of the stud at which the bowl will be installed. The length of the protruding part of the pin should exceed the width of the bowl by 10-15 mm.

Photo of a sink in a bathroom interior

If you are making holes on the surface of ceramic tiles, then in order to prevent the drill from slipping, it is recommended to attach a special mounting adhesive tape to the drilling site.

Before inserting the plumbing fixture into place, be sure to apply sealant to the edges of the bowl. To better protect the joint between the wall and the top of the bowl, you can attach a special plastic strip. It is attached with silicone sealant. If you installed it correctly, the washbasin will fit snugly against the wall and not wobble.

The washbasin model, which does not have a bracket and is attached directly to the wall, is installed in a similar way. Having marked the mounting location, drill holes for the studs. Keep in mind that the mount will be screwed in, so it should protrude 1.5-2 cm. Another type of installation is to mount the sink on the wall to which the cabinet will be attached. In this case, you need to make sure that the elements of the cabinet will not interfere with the sewer system and mixer. The plumbing fixture is attached to the wall with bolts, and the cabinet is attached to brackets.

Connecting water supply and sewerage

The final stage will be the installation of a water supply and sewer system. Before installing the mixer, it must be assembled. This must be done strictly according to the instructions that should be included in the package with the device. Remember that the rubber gaskets must fit snugly into the holes in the bowl and should not be misaligned. Check them also for defects; the gasket should not have cracks. It is necessary to wrap a sealant around the threaded connections of the valve. Then use an adjustable wrench to secure the faucet hoses.

Photo of a sink with wall mount

The siphon also requires preliminary assembly. You will not encounter any particular difficulties in this process. The main thing is not to forget about the rubber gaskets and that they fit correctly and tightly to the sink. The outlet hose is inserted into the sewer pipe. If the dimensions differ, a sealing collar must be used. It can also be sealed with silicone sealant.

After all installation work has been completed, you must turn on the water in the tap and check all systems. If you follow all the above recommendations, then installing a sink will seem like a very simple job. Remember that when purchasing plumbing fixtures, you must check the availability of all fastening parts. High-quality plumbing fixtures are easier to install.

Source: stenamaster.ru

Video on the topic: DIY bathroom sink installation. Education

Types of bath sinks

Modifications of sinks differ not only in style, shape and size, but also in the method of installation:

Corner washbasin with wall mounting

• Hanging Plumbing fixtures have a sink fastened to the wall, so the entire mass directly affects both the fastening itself and the wall, which for bathrooms is quite thin, which is not safe. That is why safe fastening of the sink to the wall is carried out only on load-bearing wall structures. The main advantage of this installation is the free space under the device, which allows for a comfortable position near it; moreover, the wall fasteners are independent of other furniture and can be located at any convenient level.

• Sink on a “tulip” type pedestal— stylized sanitary ware has a ceramic “leg”, which is the main support holding the sink with the decorative function of water supply and sewerage communications. To ensure that the plumbing fixture does not move from its place, the sink is fixed to the wall with special anchor bolts, which are not capable of bearing a weight load, but only ensure that the sink is pressed against the wall.

Installing a Tulip type sink by level

• Mounting the sink in the bathroom can be done using a supporting cabinet or tabletop- This is one of the most reliable methods of installing plumbing fixtures, because... its mass acts on a stable, strong furniture structure. This type of fastening of the sink to the countertop of the bathroom furniture helps to saturate the space with functionality, because in the niche under the sink there can be shelves that can be used to store detergents and personal hygiene items. One “but” - the cabinet under the sink does not allow you to move freely with a close approach to the sink, i.e. There is a slight inconvenience in reaching the faucet. The solution to this problem lies in choosing sink models with an elongated shape (parallel to the wall) and a side hanging over the cabinet (the cabinet is smaller than the sink itself).

Even shells of the same type can differ:

Photo of an installed corner washbasin with a cabinet

• Thus, the “seating” places for power fastening the sink to the wall and the holes for fixing it to the wall can differ significantly in the center-to-center distance between the fastening places and in the diameter of the fasteners used. Despite the wide variety of plumbing fixtures and fastening elements for them, the concept of a standard design is also applicable for plumbing fixtures, i.e. You can select a number of sink models from different manufacturers with a similar mounting arrangement.
• The main and most important difference between sinks is the material used for their manufacture, some varieties of which can easily withstand fastening the sink to the wall, while others may turn out to be fragile under the mechanical influence of the metal mount on the sink.
• Sink designs may provide for the installation of a mixer, for which models are equipped with a mounting hole. If such a model is installed with a wall mixer, the technological hole is closed with a decorative plug.

Features of sink mounting

Various models of plumbing fixtures, as a rule, have different installation methods:

Photo of a wall-mounted sink in a bathroom interior

• This is how the sink is attached to the wall: metal brackets. Moreover, the “arm” of the fastener can have several sizes, because depth (width to wall) comes in three sizes. In this case, the metal mount itself is mounted to the wall using powerful bolts or studs, but the sink, depending on the model, may not be screwed at all, but only placed on mounting brackets. Therefore, for additional fixation in such cases, sanitary sealant is used in places of contact with the wall and bracket frames, which creates an elastic “gluing”.
• Mounting a sink in a bathroom on a “leg” has its own pitfalls, because both the plumbing and the lining of the walls and floors in the bathroom are made of ceramics, which can easily be damaged if hit. Therefore, between the ceramic planes of the sink, walls and floor, install polymer gaskets with gluing with silicone sealant. Only this method of installation can ensure the absence of unpleasant ringing and squeaking noises from ceramics when struck inadvertently. It is worth considering that the bulk of the sink should act on the ceramic stand-leg, so fastening and pulling the sink itself to the wall should not cause it to rise on the support (leg), otherwise the sink will simply crack under mechanical stress.
• The easiest way is to mount the sink in the countertop, because the installation is carried out under its own weight into a specially cut-out seat in a furniture cabinet, while it is recommended to use silicone sealant to improve fixation and increase the tightness of the mating seams. The combined sink/cabinet structure usually has sufficient mass to avoid additional fastening to the wall, but if desired, they can always be fixed using anchor bolts.

Conclusion: the choice of sink model, bathroom furniture and mounting fixtures should be carried out simultaneously according to the principle of completeness, because Lack of vision for the installation method can lead to problematic situations with the breakdown of fragile plumbing fixtures. If there is a misunderstanding of the principles of fastening a sink, it is recommended that this event be carried out only with the involvement of professionals.

Source: aquagroup.ru

Bracket for a bathroom sink: types of wall mounts and installation

Today there are many types of plumbing fixtures to suit every taste. Among them are “tulip” sinks, built-in, overhead, on a pedestal and semi-pedestal, “water lilies”, and hanging.

Video on the topic: How to install a washbasin with a cabinet with your own hands

Photo of a washbasin on a pedestal

For many years now, the most used model has been the wall-hung basin. The secret of its popularity lies in ease of installation, space saving and neat design, because all communications can be easily hidden from view. The variety of forms also speaks in favor of console plumbing devices. They can be oval, round, rectangular, square, angular, or asymmetrical.

A wall-hung sink opens up a usable space underneath where you can place a small bedside table, a washing machine or store cleaning products. It is also easier to clean the floor under it, and due to the fact that it takes up quite a bit of space, such a sink will be a salvation for tiny bathrooms.

Installing washbasins to the wall will not cause difficulties even for people who do not have experience in such types of work. You can attach the sink to the wall using brackets, the variety of which is just as great.

How to choose wall mounts for sinks

The bracket is a detail that you cannot do without when fixing the washbasin to the wall. To use your sink comfortably for many years, you need to know firsthand the most reliable fasteners. In general, there are two main types of brackets: standard and specialized.

Photo of a glass sink with wall mount

The first type of fasteners is made of cast iron or welded steel, which are coated with a protective layer of paint. These parts are used for standard wall-mounted sinks.

The second type of fixtures are available complete with decorative sinks and can have a fancy, unusual shape that matches the style of the washbasin. Such fastenings for fixing on the wall are coated with special coatings made of ceramics or non-oxidizing metals, which perform protective and, at the same time, design functions. Typically the coating is either nickel plating or anodizing. It protects the fasteners from corrosion.

Photo of a sink installed above a washing machine

Choosing brackets. you need to take into account the features of the washbasin. If the sink weighs 85 kg, then the characteristics of the fasteners should indicate that they can withstand a weight that includes this figure and even more! Don't forget, you or your child may lean on the sink bowl, which will add a few extra pounds of stress that could cause damage.

Wall mounting structures

• Monolithic brackets are parts cast from cast iron in the shape of the letter “T”. They have a platform and a reinforced base for fastening.
• One of the most reliable bathroom wall mounts is the “girth” model bracket. It looks like a metal frame into which the sink is “inserted.” Due to the fact that the fastening platforms are connected to each other, and do not represent separate parts, such a system is considered the most stable.
• Frame-type fasteners are made of metal. This design can have sliding units that allow you to vary the size of the fastening. Parts of this type are arc, rectangular and sector.
• Steelwork brackets are fastening accessories produced in the shape of the letters "L" and "T" and are found in a simplified form from profiled pipes.

It is not difficult to attach such structures to the wall on your own. To begin with, it is recommended that you familiarize yourself with the standard installation requirements.

1. Water outlets should be hidden behind the installed sink. Once the work is completed they should not be visible.
2. If the washbasin creaks or wobbles after installation, this is a signal that reinstallation is necessary.
3. If leaks occur, you need to once again check the tightness of the tight connections and treat the pipe joints with sealant.
4. Fixing the sink on the wall should be done only after finishing work has been completed and after the pipeline has been installed.
5. The supply of cold and hot water to the sink must be carried out taking into account the distance between the pipes, which should be at least 15 centimeters.
6. For proper operation of all communications, the sink should be mounted level on the wall. Don't forget to use a level.
7. Before installation, be sure to check the strength of the bathroom wall. It is not recommended to attach it to drywall, as the structure will be very unreliable. If the wall is not very strong, it is recommended to use cement mortar or a load-bearing frame before installation.
8. A separate faucet for the sink is assembled and installed before installing it on the wall.

How to install a sink on the wall yourself

1. Prepare the necessary tools: level, tape, pencil or marker, drill, brackets. plastic dowels, screwdriver/screwdriver, washers, wrenches, glue and sealant.
2. Turn off the water.
3. Choose a place on the bathroom wall. where the washbasin will hang (usually the height of its fixation is 85 cm from the floor, but it can be varied depending on your preferences) and draw a horizontal line. Align the upper edge of the sink in accordance with the drawn line and mark the places where the fasteners will be fixed. On the side where the sink should touch the bathroom wall. You can find special slots near the washbasin, which must correspond to the location of the fasteners.
4. Drill holes for the brackets where you made the marks. The holes should be slightly smaller in size than the plastic dowels.
5. Blow dust out of the finished holes, pour a little glue into them and hammer in the dowels.
6. Install the fasteners that will hold the sink.
7. Coat the part where the sink will be adjacent to the wall with silicone sealant.
8. Secure the sink to the brackets.
9. Connect the siphon and sewer system.
10. Check the work for strength by trying to tug the structure from side to side. It should not wobble or creak. Turn on the water and check whether the installed plumbing structure is leaking.

Brackets for wall-mounted bathroom sinks are an essential installation accessory. Therefore, when choosing a particular mount, you must pay attention to its characteristics, as well as its design. The bathroom will become a favorite place for household members if every detail is matched to each other in accordance with the overall idea.

Source: stoki.guru

Sink brackets and other fastening elements

The sink bracket is one of the most important elements for attaching the sink. Plumbing is making serious steps forward, developing, improving in every sense. And shells are certainly no exception. The variety of solutions is also increasing, resulting in different mounting methods for them. As practice shows, wall mounting for a sink is one of the most popular ways to install this product these days.

Countertop sink with washing machine

• How to attach
• How to ensure reliable fastening
• What types of brackets are there?
• Modifications
• Fastening process

Video on the topic: Sink installation

How to attach

Since wall fastening methods provide additional comfort and allow you to get closer to the plumbing itself, we will consider two main types of such fasteners.

Installation diagram and mounting points for a wall-hung sink

1. The washbasin is installed by cutting into the hanging shelves. This installation for the sink allows you to simultaneously provide the function of a cabinet and a countertop, which the shelf performs. The result is a fairly compact, functional, practical cabinet with washbasin. By the way, the tabletop or cabinet itself, depending on the location of your plumbing, is attached to the walls with brackets. If we are talking about a small bathroom, corner solutions, then mounting fittings are used for fastening.
2. Fastening with sink brackets. It should be classified as an even more common method than the first. Such designs can be used intelligently from a design point of view, plus the fastenings are almost invisible. That's why such sink-to-wall mountings are so popular among customers.

How to ensure reliable fastening

A high-quality installation for a sink will be provided that several fairly simple conditions are met:

1. The wall must be of sufficient strength and thickness. Installation is not allowed if we are talking about installation in soft walls, or on partitions made of plasterboard. If we are even talking about overhead brackets, then the anchors must have at least a length of 40 millimeters. This means that hanging plumbing fixtures should never be attached to thin walls.
2. Different sink brackets may be made of different materials, resulting in different rigidity from each other. It is very important that the installation for the sink is carried out using brackets that are designed to support the plumbing fixtures you have chosen. The fasteners may look the same, but in reality they are designed for different loads. Some will fit under steel sinks, but ceramic products will not be able to withstand them.
3. When purchasing sink brackets, be sure to take into account their design features. We are talking about shapes, sizes, compliance with various devices and products. There are universal solutions, but there are also specialized fasteners.

What types of brackets are there?

Today there are a lot of sink mounts. You need not only to choose the right washbasin, but also to ensure its reliable adhesion to the surface. And for this, high-quality sink brackets are suitable.

1. Specialized. They are used when attaching certain models. That is, they cannot be used under every washbasin. As a rule, such fasteners are offered complete with designer, original plumbing products, which are made in a non-standard form. At the same time, such fastenings of the sink to the wall are complemented by special decorative and protective coatings. They are made of non-oxidizing metal and ceramics.
2. Standard. Of course, with the help of such sink fasteners, standard plumbing solutions can be installed on the wall. However, here it is important to take into account the fact what is the load-bearing capacity of the structure and what are its dimensions. Standard brackets for sinks are made by casting using cast iron. There are also products made of profiled steel, made by welding with the application of protective paint.

Modifications

We have already decided what kind of fastenings can be, that installation for a sink is a popular installation method, and also that brackets are in many ways suitable for a washbasin. Therefore, let’s figure out exactly what modifications of sink brackets are found today.

• Monolithic fastenings made of cast iron. They are distinguished in the shape of the letter T, they have a reinforced base and mounting platform.
• Welded from steel. As a rule, they are made in the form of the letter T or G. Although there are simplified options that are made from a square-shaped profiled pipe.
• Frame types of fastenings. They are met with sector, arc, rectangular. Some models are equipped with sliding units designed to adjust the size of the fasteners. When installing a sink, two such brackets are installed under it at once.
• Covering. This looks like a large metal profiled frame, onto which the washbasin itself is mounted directly. They are reliable and stable.

Remember that when choosing brackets for a sink or washbasin, you should take into account the maximum loads that can be placed on your plumbing. If the washbasin weighs 50 kilograms, do not take brackets designed for 75-100 kilograms. After all, you can rest your entire weight on it, as a result of which you will have to make repairs, and maybe even change the sink.

Sink bracket drawing

Fastening process

In fact, attaching sinks to the wall is quite simple.

Modern steel sink brackets

1. To ensure optimal comfort, it should be 80-85 centimeters from the floor level. But if you are a short person, or vice versa, the situation can be changed. Stand in the bathroom and try on what level you would be comfortable performing the procedures at.
2. The softer the wall, the deeper the hole should be, as well as its diameter. It’s not difficult to check the hardness of the wall; to do this, you can use a small-diameter drill and drill a hole, which will then be hidden behind the sink. If the drill goes in easily, then we recommend using a larger and longer drill to fasten the brackets. Of course, you will also need the appropriate dowels. Therefore, first check the wall and then buy fastenings.
3. Drilling should be carried out to the base under the plaster, or rather into its depth. Only after drilling into brick or concrete can the depth be stopped. Otherwise, the brackets will only stick to the plaster layer. It won't support the weight of the sink. Experts recommend choosing anchors whose length ranges from 5 to 12 centimeters.
4. A polymer plug, that is, a dowel, must be inserted into the hole, after which you can begin installing the anchor and fixing brackets.
5. If the bracket is securely fastened, it should not move under heavy load. Arm yourself with the same pliers and pull the bracket to the sides. If you can’t move it, then you did everything right.
6. Once reliability has been checked, you can begin fixing the washbasin itself. A reliable fastening for the sink is now provided to you.

As you can see, brackets are very useful, indispensable elements when installing sinks, and not only. It is important not only to choose strong, reliable fasteners, but also to choose them in accordance with the plumbing that you plan to install. At the same time, the installation of the sink will be done quite easily; you won’t have to involve specialists.

Make sure you have the necessary tools at your disposal. After all, without it, installation for the sink will be impossible. Your main tools will be a screwdriver, a drill with a set of drills, a hammer, and pliers. Armed with well-chosen fasteners for the sink to the wall, you can get to work.

Source: tavannaya.ru

Photo of a sink on a stand in a bathroom interior

Sink brackets to the wall

The original design of sanitary facilities should have not only design elements, but also functional devices with an optimal location in space. Thus, different models of sinks differ significantly in the method of fastening, which has recently become increasingly popular in the wall type.

Methods for wall mounting a sink

The wall mounting of the sink allows you to get close to the plumbing fixture with a convenient location, and there are two main types of fastening devices:

• The sink is mounted by cutting into a wall shelf, which functions as a convenient tabletop or cabinet. As a rule, a tabletop or cabinet has its own specialized fastenings, which can be in the form of brackets for mounting on a large “open” wall. When there is limited space in the room, when the sink is installed in a corner or a small opening between plumbing fixtures, the shelf-tabletop is attached point-wise to the walls using mounting hardware. Fastening the sink using the countertop is highly reliable.
• Mounting sink brackets to the wall is an equally common, and even more popular, technology for installing plumbing fixtures, because... The fastening itself is very often not particularly striking, and designer designs even add their own charm to the overall interior. Hanging sinks is a very old invention that can be easily improvised with pipes or rods driven into the wall, but you always need to take into account the weight of the plumbing fixture and the strength of the wall itself.

For reliable wall mounting of a sink, several conditions must be met:

• First of all, the wall must be strong and thick enough, so such installation on plasterboard or other “soft” walls is not allowed. Even overhead brackets for a sink to the wall require anchors at least 40 mm long for reliable installation.
• Brackets are made of different materials and have different rigidity, i.e. ability to withstand a certain weight. Thus, most lightweight fastening structures are not able to withstand the load from a ceramic sink, but are intended for the installation of metal plumbing fixtures.
• When purchasing wall brackets for sinks, it is necessary to take into account their structural features, i.e. the size and shape of the interface with the plumbing fixture, because There are various non-universal modifications.

Types of sink brackets

Wall mounts for sinks must withstand a significant weight load with a margin, so they are made of various metals and are divided into two categories:

Installation process of a wall-mounted sink

• Specialized fasteners that are produced specifically for a specific sink model. These are, as a rule, designs of designer plumbing fixtures that have a special shape. Such brackets always come complete with a designer sink model, and can be in the form of pins with a specially curved shape, “hugging” the sink pipes or interweaving rods, profiled welded structures. Fastenings must have a decorative and protective coating with specialized (ceramic) paint or a thin layer of non-oxidizing metal (anodizing, nickel plating).
• “Standardized” brackets for a sink to the wall are designed for the installation of standard plumbing fixtures, and it is necessary to take into account the load-bearing capacity of the structure and its dimensions. Fastenings are made of cast iron by casting or from high-quality profiled steel by welding, followed by protective painting.

Modifications of mounting brackets can be divided according to design features:

• Monolithic cast iron fasteners are manufactured in the form of T-shaped posts with a reinforced base and fastening platform.
• Welded steel structures in most cases also have a T- or L-shape, while there are simplified modifications made from a square profiled pipe.
• You can also find brackets in the form of frames: rectangular, arc, sector. At the same time, some models have a sliding unit for adjusting the size of the fastening. A pair of brackets are installed under the sink.
• The fastener models that “encircle” the sink are a large profiled metal frame, into which the sink “fits.” Due to the rigid ligation between the platforms fastening to the wall, such fastening is characterized by special load resistance, because under external pressure, the possibility, as in other models, of shifting a single “foot” bracket is eliminated.

The choice of bracket model must take into account the likelihood of extremely large weight forces on them and the method of fixing the sink on them, because Simply placing plumbing fixtures on supports cannot be safe.

Attaching sink brackets to the wall

• Using brackets for a sink to the wall, it is quite easy to install plumbing fixtures, and the general principles of installation are taken as a basis:
• Usually, for greater convenience, the sink is located at a height from the floor of about 800-850 mm, but adjustments to this parameter in any convenient direction are allowed.
• Before fixing the brackets to the wall, the hardness of the wall itself is checked by marking the mounting holes with a screwdriver, nail or other sharp object. If the wall surface is found to be quite soft, then it is necessary to increase the drilling depth and fastener diameter as much as possible.
• Drilling mounting holes while controlling their depth, because soft plaster will not allow the brackets to be securely fastened. The drilling depth should ensure that a hole is created in the plaster base (brick or concrete) to a depth of at least 30 mm. That is why installation anchors are individually selected from 50 to 120 mm in length.
• Polymer specialized plugs are tightly inserted into the mounting holes, into which metal anchors are screwed in to secure the wall brackets for sinks.

A securely fixed bracket should not move under significant load. Only after this can the sink be placed on the brackets with fixation, which can be done either with additional clips or with the help of plumbing sealant on the mating planes.

Installing a sink in a bathroom by plumbers from the Remzak company means affordable prices, a guarantee of reliability and tightness of the structure, correct connection to the sewer and water supply system, and comfortable operation of the sink in the bathroom for many years.

Our household service department offers its professional assistance to Moscow residents!

Call a specialist

Order installation of a sink in the bathroom

Why is it worth ordering the installation of a bathroom sink on the Remzak website:

• We have all the necessary tools and good specialists who can install the sink quickly, accurately and efficiently.
• We provide advice on the selection of plumbing fixtures
• At the customer's request, we purchase all components, including sink (sink), siphon, mixer
• We provide a full range of services: from dismantling to installing a bathroom sink
• Low prices (discount system applies)
• We provide a guarantee for the installation of a sink or sink. If during the warranty period any defect appears in the work performed, you can contact us to eliminate it.

Installation steps and methods

Installing a sink in a bathroom always involves several main steps:

• Removing the old sink
• Connection to water supply
• Ensuring proper drainage of water
• Sink mount
• Sink connection
• Setting the correct water supply
• Performance Testing

In some cases, it may be necessary to remove the old sink and replace it with a new one.

In what ways can a sink be installed? There are few basic installation methods:

• Mounting on brackets- the wall-hung sink is securely attached to the wall using a special metal structure.
• On the cabinet (a sink with a cabinet is already a sink)- the sink is securely mounted on the countertop of the cabinet and is connected to all communications using flexible hoses.
• On a semi-pedestal or on a pedestal- the bowl of the sink is well fixed to the wall, and the pedestal or semi-pedestal is placed close to it.
• On a hanging shelf- the sink is held on a special shelf, where you can also store various toiletries.

Which bathroom sink installation is best for you depends on personal preference, the design of the room, and the size of the room. Our specialist, when necessary, can suggest which installation will be best in your case.

Cost of installing a bathroom sink

What affects the final cost of installing a bathroom sink? The price of installation and connection depends on the chosen sink model, on the list of works: will it be necessary to dismantle the old sink and faucet and dispose of them, whether additional services are needed: silicone sealing, purchase of materials, preparation of walls. Below are approximate prices.

Prices for installing a sink do not include the cost of installing a faucet.

The cost of our services may vary in each specific case. To clarify prices