Hello. How grateful women are to the creator of washing machines, who freed them from monotonous labor. All that remains is to find out how to clean the washing machine, the assistant of all women, at home.

Simple ways to clean machines

Using lemon juice

The first method that all housewives use is cleansing with citric acid. How to do it? Pour 60-75 g into the powder compartment for a unit designed to load 3.5 kg of laundry; for machines with a larger load - 100-150 grams. For heavily soiled and extremely hard water – 200.

Run the mode with maximum heat without laundry. The scale that accumulates on the heating device will come off well. By the way, all advertised descaling products contain citric acid. Therefore, conclude that it will cost less.

How many times a year can you clean with citric acid? Experts recommend 2 times a year.

How to clean the rubber on the door

The rubber on the door needs to be treated vinegar. The fact is that a lot of small debris accumulates underneath it, which may end up in the drum and on the heating element.

To remove dirt from under the rubber band, wrap a piece of cloth around your finger and clean it. Perform this procedure immediately after washing, while the rubber seal remains wet.

How to get rid of smell in your car

Experts advise that in order to free the unit from odor, you must use vinegar. How to do it? Pour 1 tbsp. l. vinegar into the drum itself and turn the mode to maximum.

What to do to prevent mold?

To prevent laundry from becoming moldy, do not accumulate it in the machine, and also do not close the machine immediately after washing. Leave the door open until everything inside is dry.

It is known that the moisture that remains on the drum does not evaporate for a long time, causing mold or mildew to appear.

How to clean the filter and tray

A dirty filter must be cleaned regularly, since during long-term use a lot of debris accumulates in it, which can damage any product.

Before cleaning the filter, read the instructions on how to reach it. Then take out this element and clean it from dirt with ordinary detergents.

Detailed instructions:

1. To wash the filter, prepare a basin and a rag, then remove the compartment lid.
2. Place a rag under the bottom of the unit.
3. Remove the emergency drain hose from the filter compartment and drain the water into a basin.
4. Then remove the plug by turning it counterclockwise.
5. Wash the plug and put it back in its original place after removing dirt from the filter.
6. Rinse the filter and dry it.
7. The mesh at the end of the water supply hose should be washed once a year. To do this, unscrew the inlet hose on the rear panel of the unit.
8. Remove the mesh using pliers, rinse it, return it to its place, and connect the inlet hose to the machine.

Pay attention to the hose going from the mechanism to the sewer. If it is clogged, then an unpleasant odor cannot be avoided. This element needs to be replaced here.

The tray can accumulate lingering powder, causing poor detergent removal and mold growth.

Use proven tools:

• Mix baking soda and water in equal parts, pour into a tray, and rub with a hard sponge.
• Pour baking soda into the tray and add 9% vinegar. These components will quickly react, causing the dirt to peel off.
• You can remove the tray, place it in a container of water, add table vinegar and detergent.

Cleaning the washing machine drum from dirt

Removing the drum from dirt:

• Pour laundry bleach into the drum.
• Turn on quick wash.
• After spinning the drum for about 5 minutes, stop the machine.
• Leave the water for 1 hour.
• Then drain the water and start the rinse mode.

It's time to get to the pump. If the water isn't draining from your machine, it's time to inspect the pump. Remove the front panel, get to the filter, remove it, wash it. Unscrew the snail and remove the pump by turning it counterclockwise. Rinse, dry, put back in place.

Cleaning popular brands of machines

It is necessary to clean the filter in a car of any brand. Which filter needs to be cleaned? The fact is that the machines have 2 filters, drain and fill. So, the drain often gets clogged with various dirt. Don't forget about the filter part on the water supply hose. If the mesh becomes clogged, the device will stop drawing water. Or it could happen like this: it will collect it and immediately drain it.

General cleaning tips are written above, but there are specifics.

• The Indesit machine has a panel made of very fragile plastic, so be careful when removing the panel.
• If the filter on a Samsung unit becomes clogged, you will immediately know - code 4E or 5E will appear on the display. The unit can show this error quite often, so the Samsung needs to be cleaned 6 times a year.
• Ariston washing machine, equipped with an electronic display, will display all error codes on the display. Carefully monitor the readings and correct errors according to the instructions.

Dear friends, now you know how and with what to clean your assistant. Don't leave it in trouble and it will serve you for many years.

For household appliances to work well, they must be maintained in proper condition. For an automatic machine, this means regularly cleaning the internal and external surfaces. How to clean a washing machine from dirt and scale? Let's figure it out.

External cleaning

The main problem is the accumulation of dust on corners, joints of parts and other small recesses. Before removing such contaminants, unplug the appliance from the power supply. Choose the right tool for the job, such as a small brush with fine teeth. Dilute a mild detergent in water and thoroughly clean the body of the machine. Be careful not to fill it with water. Otherwise, moisture will get under the handles or buttons and short-circuit the equipment. Wipe everything dry with a clean cloth.

It is better to remove stains from felt-tip pen, varnish and other caustic substances immediately. Nail polish remover or alcohol will help you with this. Apply it to a cotton pad and wipe the stained area.

As a final touch, use polish or a special care product for plastic products.

Internal cleaning

To begin, clearly define your task and the scope of the work to be done. High-quality care of your washing machine includes regularly checking and tidying up the following parts: detergent tray, drum, drain hose and drain filter, rubber seals.

Powder tray

The compartment for water softeners, bleach, washing powder, etc. is constantly contaminated by residues of these substances. Particularly dangerous are clogged channels through which they are washed into the drum. In this case, you should not count on high-quality washing. To clean the tray, it should be washed every 2-3 washes. Use the rough side of a washcloth and dishwashing detergent for this purpose. For the inside of the compartment you will need a brush. After cleaning, rinse it on all sides under running water.

Drum

As soon as you notice an unpleasant odor inside the appliance, you know it’s time to clean the drum. Fill the machine with hot water, first adding the bleach. Run the wash cycle briefly to mix the ingredients. Then turn off the device and leave it for an hour. Pay attention to the overhead ribs located around the circumference of the drum. They are hollow inside and accumulate slag, silt and dirt. These elements are removable, so clean them manually in a separate container.

Sight glass

Depending on the degree of contamination, clean it with the following products: glass and dishwashing liquid, coarse salt, soda slurry, citric acid or vinegar (to remove soap scum). Chlorine-containing compounds will remove stubborn stains. The tools you need are a hard sponge, disposable wet wipes, a toothbrush or a metal scraper. Apply the substance diluted with water to the door. After 5 minutes, rub it thoroughly. If you use a scraper, try to handle the surface without applying pressure to avoid leaving scratches. Clean hard-to-reach places with cotton swabs soaked in soapy water or alcohol.

Hoses and filters

You will need a container to collect dirty water and a cloth to prevent moisture from getting under the device. Open the cover of the panel behind which the filter is located, find the hose there and drain the water from it. After making sure that it is empty, remove the filter and clean it of dirt. Then place the part back.

Rubber seals (cuffs)

These elements are located around the perimeter of the entrance window and around the circumference of the door. They need to be wiped down regularly, even during routine bathroom cleaning. For best results, use a detergent for glass, enamel and tile surfaces without abrasives. Bleach will remove heavy stains. Apply the substance to the cuff and leave for 15 minutes. After the specified time has passed, start brushing. Add 400-500 ml of vinegar to the tray and run a long wash cycle at 90 °C. When the cycle is finished, wipe the seals with a dry cloth and dry the drum.

Getting rid of scale

Lime and salt deposits accumulate on heating elements, seals and other internal parts. Over time, they corrode everything they come into contact with. This leads to breakdown and leakage of the device.

To combat scale, you will need citric acid. The amount of substance depends on the loading volume of the device (usually 100-300 g is enough). Pour it into the powder compartment and set the long wash cycle at maximum temperature.

You can replace citric acid with table vinegar. Pour 0.5 liters of liquid into the powder tray. Select a water temperature of 90 °C and turn on the non-prewash cycle. After 15 minutes, press pause, and then after an hour, start the cycle again. After the program is completed, mix vinegar with water in a 1:1 ratio, dampen a cloth and wipe the rubber seals. Microorganisms that emit a bad odor may remain in their folds. Descale your machine every 6 months. If the water in your region is hard, then once every 3-5 months.

Removing rust

Rust can form in areas that have been exposed to moisture and at the joints on the back of the appliance. Specialized drugs will help remove it. Apply the composition to the problem area and leave for a few minutes (according to the included instructions). Then remove the rust and wipe the surface with a damp cloth. When working with aggressive compounds, wear rubber gloves and ventilate the room.

If you're looking for a cheaper option, use lemon juice and vinegar. Mix the ingredients in equal quantities and apply to rusty spots. After a couple of hours, brush and rinse off the product. Repeat the procedure if necessary.

4.50 out of 5 (8 Votes)

Reading time: 1 minute

Today, an automatic washing machine is a faithful assistant to almost every housewife or owner. The trouble-free device is capable of washing mountains of various products in a couple of hours, sometimes in such a deplorable state that we would not be able to cope with such a task in a day by hand. But how reliable is it? The washing machine needs cleaning, and so seriously that without it, one day the device will simply fail. And this is not only wiping off dust, but a number of other equally complex procedures. We will tell you further how to rinse a washing machine correctly.

Each part of the machine needs a special type of cleaning. Which one - see the continuation of the article.

Drum

The most convenient way to clean the drum is when this function is already provided by the manufacturer of your washing machine. You add detergent, turn on the desired program (it’s called “ auto drum cleaning") - and voila!

For those whose washing machines"are not equipped with such an excellent opportunity, we can recommend the following to get rid of scale and dirt on the drum:

1. Pour 100 ml of any bleach into the drum itself.
2. How to rinse " washing machine"? Without adding laundry, activate the washing mode with a temperature of at least 60 degrees.
3. You can clean the drum in a similar way using citric acid and soda - scroll through our tips further.

Advice! Make it a rule to leave the machine door open after each wash until it dries completely.” entrails" This way you will also get rid of the unpleasant musty smell from the drum.

Powder compartment

Many of us also neglect the department for detergents - they poured in powder, poured in liquid substance and that’s it. But if we bypass it by cleaning, we will get powdery build-ups, accumulations of dirt and even mold, which will happily be washed together with the laundry in the drum.

And cleaning the washing powder compartment is very simple:

1. In accordance with the instructions, remove this container from the " nests».
2. Arm yourself with a sponge or, better yet, an old toothbrush. Lather your tool with laundry soap and, section by section, remove all dirt.
3. Difficult to erase plaque? A toilet bowl cleaner or any cleaning liquid containing chlorine will help. Pour 20-30 ml into a container and let it brew for several hours. Mold and pieces of plaque will come off on their own; all you have to do is rinse the compartment under running water.

This simple preventive cleaning is best done every 3-5 wash cycles.

Advice! To clean the compartment as little as possible, use neutral detergents for washing.

heating element

The most problematic element in a washing machine is the heating element. Especially if your water supply flows with water of increased hardness - the impurities in it of salts, rust, and metals are much more than normal. With each wash, this element under such conditions becomes overgrown with a layer of scale. When the heating element is too covered with it, the machine will not turn on or will sadly fall silent in the middle of operation.

The heating element is usually cleaned in the following way:

1. Buy several packets of citric acid. For example, a machine with an average load of 5 kg will require 5 packages of powder.
2. Pour 4/5 of the bags into the detergent container, and 1/5 into the drum.
3. Turn on any washing mode for which you can activate the highest temperature - up to 90-95 degrees.
4. The scale will come out through the drain hose. The main thing is to make sure that its large pieces do not clog this element.

Advice! This cleaning can be done up to 2 times a month.

Cuff

You should not neglect the rubber seal between the drum and the door. Dirt accumulates on it, and sometimes mold grows.

What to wash with " washing machine" this time? You can clean it in two ways:

• Light contamination: soda, Pemolux, etc.
• Mold, unpleasant smell: “Duckling”, “Komet”, “Domestos”, whiteness.

The cleaning instructions are simple:

1. Apply a little product to a rag or napkin. Wipe the rubber.
2. Pull the cuff towards you and clean the metal lining underneath.
3. In this way, clean the rubber folds inside the cuff itself - it is better to use an old toothbrush for this.
4. Finally, rinse the product off the element by wiping it with a cloth soaked in clean water.

Advice! Do not use vinegar essence or chlorine-containing products - they can damage the gum.

Drain pump filter

Few people know where this element is located, much less how to clean it. But it is precisely because of this that the machine may one day stop working, and you will pay a considerable amount of cash to the technician for a procedure that you could easily perform yourself.

So let's find it first. Usually the filter is “hidden” on the front side of the device behind a round, rectangular cover. Found it? Now let's move on - how to wash the “washing machine” in this part of it:

1. Open the cover ( The instructions for the car should tell you how to do this specifically for your model). There will be a cork in front of you, which means you have opened the right hole.
2. Place a container under the plug first - if the filter is clogged, water will flow out.
3. Now it's time to pop the cork. Behind it you will see hair, strings and other debris. If the filter has not been cleaned for a long time, then the smell may not be very pleasant.
4. With your gloved hands, carefully remove all this “wealth” and wipe the inside of the filter dry with a dry soft cloth.
5. Now all that remains is to put the plug and lid back in place.

Advice! Thus, it is best to clean the filter after each wash. As a last resort, remember to do this 1-2 times a month.

Inlet hose filter

It would also be very useful to clean the filter of the inlet hose - the one through which fresh water enters the machine. Again, due to the poor quality of tap water, over time it becomes clogged with sand and rust. As a result, the machine refuses to work.

We will clean it like this:

1. Arm yourself with pliers ( pliers) and an old toothbrush.
2. Be sure to turn off the water supply valve to the machine!
3. Turn the back of the machine towards you. Find the place where the inlet hose goes into it.
4. Unscrew the nut securing the hose counterclockwise.
5. When you look inside the hose, you will notice a small mesh filter. Pull it out with a tool.
6. Clean the part from dirt with a toothbrush.
7. Insert the filter into place and tighten the hose.
8. You can also wipe the back wall from dust.
9. Turn on the water supply tap to the machine, and screw the device into its usual place.

At the end of the cleaning, all that remains is to wipe off dust from the glass door and the body of the washing machine. That's all! The video in this article will show you more tips.

Folk remedies

We will share with you folk methods of cleaning a washing machine, which are aimed at combating scale. Its harm to the washing machine is obvious:

• Increased electricity consumption. Scale gradually covers the heating element and the element requires more and more energy to heat up.
• The direct cause of machine breakdown is the heating element covered with scale, it works, as they say, “ on one's last legs" By the way, if such “ tortured» The heating element cannot be replaced in time; the problem can lead to a more expensive breakdown of the device’s software module.
• Scale is an excellent environment for mold to form.

Acetic acid

Many housewives trust these methods.

Cleaning the drum and cuff from dirt and unpleasant odors

Wear gloves when handling vinegar: 1. Pour ½ cup of 9% acetic acid into the detergent compartment. 2. Select the longest program at high temperature. 3. When the machine warms up, pause the cycle. Let the solution act for 1.5-2 hours. 4. Resume the cycle. 5. Clean the drain filter from the cleaned scale. 6. Mix 50 ml of acetic acid with 1 liter of water. Wipe the cuff, drum, and door manually. 7. To eliminate the unpleasant vinegar smell, it is advisable to include a short washing program without laundry.

How to wash laundry detergent from detergent containers? Choose a container in which you can soak the entire container. Dilute a glass of 9% vinegar in warm water. Leave the container to soak for a day. At the end, it will be enough to rinse it under running water and dry it.

Advice! If you have 70% vinegar essence, then it must be diluted with water 1:7 to obtain a solution equal in concentration to 9% vinegar.

Soda Ash

To clean the inside of the machine from scale and unpleasant odors, we need soda ash, not baking soda - Na2CO3. It is better to carry out the procedure with her participation at least once a month. We have placed the instructions in the table.

Cleaning the drum and cuff	We will proceed as follows: 1. Prepare the required amount of soda solution: 1 part powder to 1 part water. 2. Wearing rubber gloves, apply the mixture thickly to the inside of the drum, onto the cuff, not forgetting its internal folds. 3. Leave the solution for half an hour. 4. Rinse off with a damp cloth, cleaning it periodically with water. 5. Set a short wash program without laundry.
Cleaning the detergent container	Also prepare a solution of soda ash with water ( one to one). Coat the container thickly with it, paying special attention to dirty, boiled, and moldy areas. After 30 minutes, rinse under running water and dry.

Advice! Soda ash is an excellent remedy for scale formation on the internal elements of the machine. Therefore, make it a rule to add 2 tablespoons of it with each wash. An exception should be made only when loading woolen or silk products into the drum.

Copper sulfate

A less common, but quite effective remedy that specifically helps against mold that has settled in the “washing machine”.

Cleaning with it is simple:

1. Prepare the following solution: 30 g of powder per 1 liter of water.
2. Using this mixture, carefully treat the internal surfaces - the drum, the detergent compartment, all the folds of the cuff.
3. Leave it for a day.
4. After time has passed, wash the treated areas with a clean cloth soaked in water.
5. Pour the powder into the compartment and run the wash program without laundry. After this, it is advisable to run another one, but without detergent.

Professional products

Antiscale Five Plus
Dr.Beckmann AntiKal
Frau Schmidt Electrolux remedy

• "Antiscale";
• Five Plus;
• Filtero;
• Beckmann;
• AntiKal;
• Descaler;
• Frau Schmidt;
• line of cleaning products from Candy, Electrolux, Bosch, etc.

Prevention measures

To keep your car clean longer and serve you faithfully for a long time, you just need to follow a few easy-to-remember tips:

• Use as much detergent and conditioner as the manufacturer recommends. Excess will not lead to things stretching better - the product will settle in the “insides” of the machine, accumulating growths on them.
• Manually collect small debris from things and pockets so that it does not clog the drain filter.
• It is better not to languish washed items in the drum for a long time after washing, but to immediately take them out and send them to dry. This is the best prevention of mold and unpleasant smell from the car.
• Make it a habit to keep the machine door slightly open when not using the washing machine.
• Scale on the internal elements crystallizes if you set washing programs with heating to 70-75 degrees. To prevent this from happening, wash at lower temperatures. And if you choose programs with heating only up to 40-50 degrees, then the heating element will not heat up at all, which means scale will not form on it.

The key to cleanliness and long service life of the automatic machine is also detergents for washing. They must contain elements that prevent scale formation. It is also important not to forget about preventive measures and regular cleaning of all components of the washing machine.

A washing machine is one of the most useful household inventions, which can significantly save time and effort on washing. Not everyone knows that an automatic car also needs cleaning. If you do not regularly clean your washing machine, then over time the laundry will not wash properly and will acquire an unpleasant odor. To avoid this, you need to wash all components of the machine: from the drum to the powder compartment. The main thing is to choose the right cleaning products that will not harm the equipment.

If the laundry unexpectedly remains dirty after washing or acquires an unpleasant odor, then it is necessary to clean the washing machine.

It is advisable to wash all accessible parts, from the body to the drum.

Outside

To maintain the neat appearance of your automatic machine, you need to regularly wipe away any traces of powder and other detergents from its body. You just need to wipe the outside of the machine with a clean damp cloth. If the dirt is old, you can use a soap solution.

Before starting the procedure, you must disconnect the equipment from the network. Also, when washing the body of the washing machine, carefully wring out the cloth so that water does not get on the internal parts. This may cause a short circuit.

Powder compartment

Usually the powder compartment is ignored when cleaning the washing machine. But this is where mold and unpleasant odors most often appear due to stagnant water. When washing, water passes through this section and carries with it dirt that falls directly on the clothes in the drum. Therefore, you should wash the powder compartment every 5-7 washes.

To do this, you need to remove the tray from the machine and rinse it thoroughly with a sponge or brush. We must not forget about the place for the fabric softener, where a white residue often forms. Bathroom cleaning products will help you deal with it.

Filters

Typically, an automatic machine has 2 filters: a coarse filter, through which water flows from the water supply into the machine, and a drain, which traps debris that gets into the tank along with clothes (threads, fabric fibers and other small items).

Over time, these filters may become clogged. Then they will need urgent cleaning. For this purpose, you can call a specialist, or you can try cleaning the filters at home.

Before cleaning, you must turn off the water.

Procedure for washing the coarse filter:

1. If the equipment is not built into the wall, then this filter can be found in the hose located on the washing machine itself.
2. At the end of the hose there is a mesh that does not let debris out of the water supply. This mesh must be taken out and thoroughly cleaned with cotton swabs.
3. If the filter is very clogged, you should unhook the entire hose and connect it to the pipe with the reverse side. Then point the other end into the bucket and turn on the water at maximum pressure. The flow of water will remove all debris from the filter.

1. Most often this filter is located at the bottom. To get to it, you need to open the lid, under which there is a tube and a round part with a handle. The latter is the drain filter.
2. Direct the drain hose into a bucket and remove the plug to get rid of the water.
3. Then unscrew the drain filter and clean it with cotton swabs.

If the washing machine is designed differently, you can refer to the instructions or call a specialist to your home.

Drum

After both filters are cleaned, you should move on to cleaning the machine drum. It consists of a rubber seal and the tank itself.

First of all, you need to clean out the accumulated debris and wash off the remaining cleaning products from under the gum. This can be done with a dry cloth. It is under the elastic band that coins, buttons and other small items that fall out of clothing usually accumulate.

The tank itself may contain dirt and mold. Therefore, you should use available means to clean it.

Soda

Regular baking soda is a good remedy against the formation of fungus in the drum of a washing machine.

Instructions:

1. Mix soda and water in equal proportions. Since baking soda is abrasive and can scratch the surface of the drum, you need to make sure that the baking soda is completely dissolved in the water.
2. Moisten a soft rag or sponge with the resulting solution and wipe the internal surfaces of the machine, paying special attention to the rubber seal.
3. Rinse off the soda with warm water.
4. Wipe cleaned surfaces with a dry cloth.

Lemon acid

Citric acid is very effective in combating unpleasant odors and other contaminants inside the washing machine. To use this tool, you need:

• pour 200 g of citric acid into the powder tray;
• start washing without clothes at a temperature of at least 60 degrees;
• After the machine has finished operating, turn on the rinse mode.

It is advisable to use this method no more than 3-4 times a year, since frequent use of citric acid can harm the rubber elements of the machine.

Vinegar

Vinegar will help remove scale from the drum.

To do this, you need to pour 2 cups of 9% vinegar essence directly into the drum and start the machine, selecting the longest wash mode with the maximum temperature. In this case, there is no need to put clothes.

A few minutes after the start of washing, you need to pause the automatic machine and wait 30-60 minutes, depending on how dirty it is. At this time, vinegar will actively fight scale.

After the specified time has expired, you should start the machine again and wait until it finishes working.

How to get rid of scale

Scale appears over time in almost any automatic machine due to hard water. Limescale deposits form on all surfaces of the washing machine with which such water interacts. Limescale can lead to equipment breakdowns and leaks. It is recommended to descale the machine 3-4 times a year.

Cleaning with citric acid:

• pour citric acid into the powder compartment;
• run the machine without clothes, setting the maximum temperature;
• after finishing washing, mix 9% vinegar with water in equal proportions;
• moisten a rag with the prepared solution and wipe the drum with the rubber seal;
• Rinse surfaces thoroughly with warm water.

In this case, vinegar helps eliminate bacteria remaining after descaling.

Cleaning with White:

• pour 200 ml of White directly into the drum of the washing machine;
• set a long mode with a temperature of at least 60 degrees and start the machine without laundry;
• After finishing washing, you should turn on the rinse mode, which will help remove the smell of bleach.

Bleach quickly removes scale, but during the washing process a sharp and pungent smell of chlorine appears. Therefore, it is recommended to open all doors and windows in the room.

In addition to the methods listed above, you can use special products designed to remove scale.

Preventing scale formation

In order not to suddenly encounter a breakdown of your washing machine, you need to familiarize yourself with various methods of preventing the occurrence of scale:

1. Add with each wash substances,. This can be store-bought Calgon or regular citric acid. You can also sometimes add soda ash. It reacts chemically with salts.
2. Use low temperatures when washing. Scale is formed under the influence of hot water. Therefore, it is advisable to wash things in cold or slightly warm water. If cleaning clothes requires high temperatures, then the item must be washed first. This method requires additional effort and time, but it helps to extend the life of the automatic machine.
3. Set filters, softening water in the apartment. Before purchasing a filter, you must have the water from your home analyzed. Then, based on the analysis results, you can select the most suitable filter in a specialized store.

Filters require more investment, but will protect all devices that come into contact with water.

Methods for removing mold and unpleasant odors

Unpleasant if a residue from detergents remains on the walls of the drum. This leads to rot and mold.

To get rid of unwanted aroma, you need to pour washing powder into the machine and turn on the unit, setting the maximum washing temperature. There is no need to put clothes in the drum. After washing, wipe the drum and rubber seal with a dry cloth. Leave the door open after the procedure.

Mold can also appear if you frequently use a gentle, low-temperature wash cycle. After all, bleach and high temperature are detrimental to fungus.

Most often, mold accumulates in the detergent compartment, behind the rubber seal and in the drain hose. These parts must be removed and rubbed with a brush dipped in soapy water.

An effective way to remove mold:

• pour 1 liter of bleach into the powder tray;
• run the wash at maximum temperature without clothes;
• after 10 minutes turn off the machine;
• wait 1-2 hours;
• pour 200 ml of 9% acetic acid into the conditioner compartment;
• start the wash again;
• After finishing work, turn on the rinse mode.

The methods listed will help you effectively deal with various contaminants that occur in the machine. All that remains is to choose the most suitable method and enjoy the cleanliness and pleasant aroma of washed items.